background image

 

 

 

 

15 

Better Packages, Inc. 

Warranty Information

 

 

The manufacturer warrants each new Better Packages machine and accessory to be free from defects in material 
and workmanship under normal and proper use. Its obligation under this warranty being limited to replacing or 
repairing any defective parts within the time period indicated for the specific model after delivery (at the company’s 
discretion) to the customer. Wearable parts such as shear blades, water bottles and caps, water brushes and motor 
brushes are not covered under the warranty. Machines used for any reason not intended by the manufacturer will not 
be considered for warranty protection. 

The company will replace or repair (at the company’s discretion) any defective parts within the warranty period, on a 
no-charge basis. The Authorized Distributor/Service Center will furnish, without charge, within the time period 
indicated for the specific model, necessary labor to service the machine. 

If customer wishes, they may forward any machine listed below with authorization from Better Packages or an 
Authorized Distributor/Service Center for warranty service. Any item shipped for warranty service must be shipped in 
the original factory carton and properly packed with the original protective packaging inserts or a secure carton that 
will properly protect the unit during transit. Units received improperly packed are subject to costs associated with 
damage caused during transit.  These costs will be the responsibility of the customer. All associated shipping or 
freight costs related to items shipped for service are the sole responsibility of the customer. 
 
For service under this warranty, call or write your nearest Better Packages Distributor/Service Center or Better 
Packages, Inc. Ansonia, CT at 800-237-9151 (US only) or (203) 926-3700. To locate your local Authorized 
Distributor/Service Center, 

visit

 

www.betterpackages.com

. Transportation charges on machines or parts returned 

to Better Packages for service must be prepaid by the customer.  Customers will be responsible for freight expenses 
on parts or machines returned to them.   
 
Better Packages’ ship-to address is:  4 Hershey Drive 
                                                           Ansonia, Connecticut 06401

 

 

 

 
Product Warranty* 

Model 

Parts 

Labor 

Better Pack

®

 755e Series 

2 Years 

6 Months 

Better Pack

®

 555e Series 

2 Years 

6 Months 

Better Pack

®  

500 Series 

2 Years 

6 Months 

Better Pack

®

 333 Series 

2 Years 

6 Months 

TapeShooter

®

 404 

2 Years 

6 Months 

Packer

® 

3S 

2 Years 

6 Months 

Better Pack

® 

PS2A 

1 Year 

6 Months 

 
*When servicing a Better Packages product, genuine Better Packages replacement parts should be 
used.  Any other parts used will void all existing warranties along with UL, CE and CSA 
certifications and may create a safety hazard. 

 

 

This warranty statement dated May 1, 2014 supersedes all other prior published statements. 

 

Summary of Contents for Better Pack 755e SA
















Reviews: