manualshive.com logo in svg

BETCO Stealth ASD20BT, Operator And Parts Manual, Page: 60 / 68

Share
Download
BETCO Stealth ASD20BT Operator And Parts Manual Download Page 60

60

ELECTRICAL DIAGRAM - BEFORE SERIAL NUMBER 214999999

1. ELECTRIC HARNESS INSPECTION

1.  Verify the functionality and adjustment of the 

micro switches

 of the handlebar control.

2.  Verify that the micro switches are pressed with the switch lever in rest position and 

that in that condition the micro switch lever has about 

0.5 mm of movement

. 

3.  Verify the functionality and conditions of the 

power contactors

 of the 

self recovery 

fuses

 and of the connections of the control card. 

4.  Verify the condition of the 

brake resistor

 and its connection.

5.  Verify the conditions of the speed control card and the functionality of the 

direction 

contactors

.

ELECTRICAL SYSTEM

VACUUM 
MOTOR

BRUSH MOTOR

Potentiometer

TRACTION

MOTOR

1.  Verify the functionality of the variable speed control card.

2.  If necessary adjust the traction card:

•  Lift up at least one of the traction wheel .

•  Remove the handlebar for access to the electric controls.

•  Set-up the tester in volt-meter with 50V maximum.

•  Put the tester pins on the faston 

M+

 and

 M-

 of the speed control card.

•  Turn on the key master switch.

•  Pull the switch lever until you hear the forward first 

micro switch click

 (first speed).

•  The tester has to show a voltage between 14 and 15V. If the reading is different 

adjust the 

trimmer

 (first speed) to have the right output voltage.

•  Completely pull the switch lever until the second (maximum) speed 

micro switch 

is pressed. A voltage of 24V (the same as the battery voltage) has to be read; in op-

posite case verify the power connections and the conditions of the battery.

•  Acceleration adjustment: Adjust on the 

“ACC” trimmer

 to let it be between 30° and 

45° respect the central position rotating clockwise. Verify that with this regulation the 

machine reach the maximum speed in 4 second.

•  Check the backward direction .

•  Check the braking power of the traction motor. At maximum speed the machine has 

to stop in about 1 meter.

ADJUSTMENT/INSPECTIONS OF THE VARIABLE SPEED CONTROL CARD

Summary of Contents for Stealth ASD20BT





































































Reviews:

No comments