background image

1

12

Caution 1: When flying in Normal mode, please try to choose an indoor or windless outdoor 
environment.

keeping the flight height within 0.5m-5m. Meanwhile, the outdoor flight height should 

not exceed 5m. When in a harsh environment, such as flying in a strong wind, the quadcopter may 
not be controlled, drift and fall.
Caution 2:  If you want to experience the auxiliary flight function in both altitude and horizontal 
positions, when in normal mode (N MODE), sport mode (S MODE), and manual mode (M MODE), 
please try Cetus or Cetus Pro kit, which supports more flight modes.

directional joystick controls the tilt direction and tilt angle of quadcopter. It also has an 
auxiliary flight function, which can assist in adjusting the altitude position, but can not 
adjust the horizontal position. 

Each battery provides 4-5 minutes of smooth flight. When LED indicator on the 
quadcopter started flashing red, indicating the battery is low on power and needs to be 
recharged. Charging steps are as follows: 

● Connect the charger with a Type-C port USB cable;
● Connect one or two batteries to the port on the right of the charger and the charger’s 
LED indicator will turn solid red while charging;
● When the charger’s LED indicator turns solid green, charging process is complete.

3.6 Battery Charging

Obstacle

0.5~5m

Summary of Contents for 01020010













































Reviews: