Betafence Robusta Plus Manualline Download | Manualshive

Page: 1 / 15

background image

1

Created 11.08.2014:

Approved 11.08.2014:

Bodo Kiesewalter

Guide line to check and repair the safety equipment of the

Robusta Plus Sliding Gate ver. 1.0

Contents

1. Technical data of the Robusta Plus Sliding gate ............................................................................. 1

2. Checklist in case of failure Drive unit C720 / 721 ........................................................................... 2

3. Checklist in case of failure Drive unit C746 / 844 ........................................................................... 3

4. Manual for to check the safety devices of the sliding gates guiding post / lock post .................... 4

5. AERF System (Wireless Band) ......................................................................................................... 9

6. Installation of resistive safety strip at the front of the wing of Robusta Plus sliding gate ........... 11

6.1 Table of required resistive safety strip (SAP code) according the height of the gate ................ 11

6.2 Procedure to connect resistance safety strip to the AERF system ............................................. 12

Electrical drawing safety strips E780 ................................................................................................ 14

Electrical drawing photocells E780 ................................................................................................... 15

1. Technical data of the Robusta Plus Sliding gate

Type of FAAC unit:______________ Dimension:______________ Construction year:_______

1
2
3
...
»

Summary of Contents for Robusta Plus
















Reviews:

No comments

Related manuals for Robusta Plus

Brand: Gerni Pages: 60

Compact Top Extra Large

Brand: Exo Terra Pages: 17

Brand: Gibson Pages: 2

Brand: Kalamazoo Pages: 4

KENALL MILLENIUM METREX METEL Series

Brand: LEGRAND Pages: 6

SensorSMART i-Q350LX PCE

Brand: IDENTEC SOLUTIONS Pages: 25

Brand: Carpet Cleaner Pages: 8

Brand: WaveLynx Pages: 14

Brand: Heathkit Pages: 8

Brand: Audio enhancement Pages: 3

Brand: Alien Pages: 6

ACTLAN - INTERFACE

Brand: ACT Pages: 2

Turboflotor Blue 3000

Brand: Aqua Medic Pages: 36

Brand: Sphenic Technologies Inc. Pages: 4

Rospri R 36 Plus

Brand: Rothenberger Pages: 64

Brand: Deer Fence Pages: 5

INMOTION COMPACT

Brand: Altec Lansing Pages: 2

Brand: Gallagher Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands