Beta Ultra Dottie II Operating Manual Download Page 40

Page: 40 / 41

39/40

The serial interface is configured as follows in the factory:

• Standard RS232 with TxD cable

• 115,200 baud

• 8 bit, 1 stop bit, no parity

*For connection to a USB port the use of a

KEYSPAN High Speed USB Serial Adapter USA-19HS

is recommended.

4.3 Declaration of conformity

CE-DECLARATION OF CONFORMITY

The undersigned, representing the following manufacturer

Beta Industries

herewith declares that the product:

Ultra Dottie II
Plate Measuring Device

is in conformity with the provisions of the following CE

directive(s) (including all applicable amendments):

73/23/EEC

Electrical equipment for use within specified voltage limits

89/336/EEC

Electromagnetic compatibility

and the standards and/or technical specifications referenced

overleaf have been applied.

The last two digits of the year in which the CE marking was affixed:

Summary of Contents for Ultra Dottie II










































Search results

Summary of Contents for Ultra Dottie II

Reviews:

Related manuals for Ultra Dottie II

Brands by name

Popular brands

Beta Ultra Dottie II, Operating Manual

Search results

Summary of Contents for Ultra Dottie II

Reviews:

Related manuals for Ultra Dottie II

Brands by name

Popular brands