background image

NOTE:

 The WATER HEATER rate may change in the conditions below:

• When the outdoor temperature is below 15°C (59°F).

• If the cover is not in position when the heating function is activated.

NOTE:

 To display the current water temperature, run the filter system for at least a 

minute. 

The water temperature as tested by an external thermometer may vary from the 

temperature as displayed on the spa panel by as much as approximately 2°C(35.6°F).

POWER-SAVING TIMER LED:

 

This flashing LED means you are setting the heating duration. The light will 

be on when the heating function starts to work.

This flashing LED means you are setting the number of hours FROM NOW 

when the heater will activate. When the light is on, the Power-Saving 

Timer function is set.

I. WATER FILTER BUTTON: 

This button turns the filter pump on and off.

The light above the Water Filter Button displays red when activated.

E/G. TEMPERATURE ADJUSTMENT BUTTONS:

 Pressing the 

Temperature Increase or Decrease buttons will cause the LED to flash. 

When it is flashing you can adjust to the desired temperature setting. If 

you hold these buttons down the values will rapidly increase or decrease. 

The new and desired temperature setting will remain on the LED display 

for 3 seconds to confirm the new value.

NOTE:

 The default temperature is 35°C (95°F).

NOTE:

 Temperature adjustment ranges from 20°C (68°F) to 40°C 

(104°F).

F. ON/OFF BUTTON:

 Press this button for 2 seconds to active the control 

panel buttons and the light turns to green. Press this button for 2 seconds 

to turn off all currently activated functions.

D. MASSAGE SYSTEM BUTTON:

 Use this button to activate the 

massage system, which has a 30-minute auto-shutoff feature. The light 

above the Massage System Button displays red when activated.

IMPORTANT:

 Do not run the Massage system when the cover is 

WINTER USE INSTRUCTIONS

 

• You can keep the spa on during winter when the temperature is lower than 

6°C(42.8°F). The Freeze Shield™ system automatically keeps the water temperature 

between 6°C(42.8°F) and 10°C(50°F), and it will prevent the water from freezing.

Important: 

If the water temperature is below 6°C(42.8°F), the spa heater must always 

Water Maintenance

Many pollutants in the water settle on surfaces below the water line. These 

pollutants can cause bacterial, algal or fungal growth. It is recommended that spas 

are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may 

develop on the accessible surfaces below the water line or high concentrations of 

salts or unwanted reaction by-products may also occur. Depending on hygienic 

condition, cleanliness, visibility, odour, debris and stains, it is recommended to 

change the water completely and clean/disinfect the spa. When emptying the spa, 

the regulations and the instructions for draining the water shall be observed.

Keeping your spa water clean and chemically balanced is necessary. Simply 

cleaning the filter cartridge is not enough for proper maintenance, we recommend 

you use pool chemicals to maintain water chemistry and chlorine or bromine tablets 

(do not use granules) with the chemical dispenser.

Water quality will be directly related to frequency of use, number of users and 

overall maintenance of the spa.  The water should be changed every 

3 days if there is no chemical treatment being performed with the water.

It is highly recommended to use tap water for spa filling to minimize the influence of 

unwanted content, such as minerals. Barefoot areas and relaxing areas shall be 

cleaned as well. No cleaning water may flow into the spa or spa water cycle. The 

dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.

Note:

 We recommend you take a shower before using your Lay-Z-Spa, as cosmetic 

products, lotions, and other residues on the skin can quickly degrade water 

quality.To use the chemical dispenser, please follow the below instruction.

attached. Air can accumulate inside the spa and cause irreparable 

damage to the cover and bodily harm.

NOTE:

 Heat and massage system work together to create a warm 

massage experience.

H. CELSIUS/FAHRENHEIT TOGGLE:

 The temperature can be displayed 

in either Fahrenheit or Celsius.

12

Summary of Contents for S100103





















Reviews: