background image

A. LOCK/UNLOCK BUTTON:

 The pump has a 5-minute auto-lock, this 

light will turn on. To lock or unlock the pump, place a finger over the 

lock/unlock button for 3 seconds.

C. HEAT BUTTON: 

Use this button to activate the heating system. When 

the light above the heat button is red, the heating system is activated. 

When the light is green, the water is at the set temperature and the 

heating system is at rest.

NOTE:

 If the heating system is activated the filtration system will 

automatically start.

NOTE:

 After turning off the heating system the filtration system will 

continue to operate.

NOTE:

 If the spa heater is on when the water temperature is below 

6ºC(42.8°F), the heating system will warm the water until 10ºC(50°F) 

automatically.

B. POWER-SAVING TIMER BUTTON:

 Designed to help avoid wasting 

power by setting the time and duration of the heating cycle for the spa.

This way, you can enjoy your spa at the time you desire, without needing 

to leave the heater on at all times.

A

B

C
D

G

E

F

H

I

D. MASSAGE SYSTEM BUTTON:

 Use this button to activate the 

massage system, which has a 30-minute auto-shutoff feature. The light 

above the Massage System Button displays red when activated.

IMPORTANT:

 Do not run the Massage system when the cover is 

STEP 1: Set the heating duration

1. Press the     button unit the     LED starts to flash.

2. Press the     or     button to adjust the heating duration (From 1-999 hours).

3. Press the     button again to confirm the heating duration.

STEP 2: Set the number of hours FROM NOW when the heater will activate

1. After setting the heating duration, the     LED starts to flash.

2. Press the     or     button to adjust the hours until time of activation (From 0-999 hours).

3. Press     button again or simply touch nothing for 10 seconds to confirm the setting. The       

LED will light steadily, and the countdown to heater activation will begin.

To modify the timer settings: Press the     button and use the     or     button to adjust.

Cancel the setting: Press the     button for 2 seconds.

NOTE: After setting, the screen flashes the current temperature and time alternately.

NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 999 hours; 

Reservation time adjustment (the number of hours FROM NOW when the heater will begin to 

function) may be set from 0 to 999 hours. If the timer is set at 0 hour, the heating system will 

activate immediately.

Note that the timer is one time per use - the user sets the duration of the heating cycle, and 

how many hours from now the heating cycle begins. The timer does NOT repeat until reset.

Water Maintenance

Many pollutants in the water settle on surfaces below the water line. These 

pollutants can cause bacterial, algal or fungal growth. It is recommended that spas 

are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may 

develop on the accessible surfaces below the water line or high concentrations of 

salts or unwanted reaction by-products may also occur. Depending on hygienic 

condition, cleanliness, visibility, odour, debris and stains, it is recommended to 

change the water completely and clean/disinfect the spa. When emptying the spa, 

the regulations and the instructions for draining the water shall be observed.

Keeping your spa water clean and chemically balanced is necessary. Simply 

cleaning the filter cartridge is not enough for proper maintenance, we recommend 

you use pool chemicals to maintain water chemistry and chlorine or bromine tablets 

(do not use granules) with the chemical dispenser.

Water quality will be directly related to frequency of use, number of users and 

overall maintenance of the spa.  The water should be changed every 

3 days if there is no chemical treatment being performed with the water.

It is highly recommended to use tap water for spa filling to minimize the influence of 

unwanted content, such as minerals. Barefoot areas and relaxing areas shall be 

cleaned as well. No cleaning water may flow into the spa or spa water cycle. The 

dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.

Note:

 We recommend you take a shower before using your Lay-Z-Spa, as cosmetic 

products, lotions, and other residues on the skin can quickly degrade water 

quality.To use the chemical dispenser, please follow the below instruction.

USING THE SPA

attached. Air can accumulate inside the spa and cause irreparable 

damage to the cover and bodily harm.

NOTE:

 Heat and massage system work together to create a warm 

massage experience.

11

Summary of Contents for S100103





















Reviews: