S-S-003665
PUMP OPERATION
B
J
H
G
F
E
D
A
C
I
RESET
Heating Reset
When using the Lay-Z-Spa for first time, or after a long period of inactivity, be sure to press
the reset button on the pump using a small and thin object.
If the temperature on the control panel (or the water temperature) has not changed 4-5 hours after
activation of the heating system, use a thin object to press the RESET BUTTON, and restart the heating
system.
IMPORTANT:
The heating System will not operate if the outside temperature is above 40ºC (104 ºF
)
or if
the Lay-Z-Spa is under direct sunlight. Under these conditions, please wait until a cooler time of day
before pressing the RESET BUTTON with a thin object and restart the heating System.
The pump has a 5-minute auto-lock. To lock or unlock
the pump, place a finger over the lock/unlock button for
3 seconds.
Use this button to activate the massage system, which
has a 30-minute auto-shutoff feature. The light above the
Lay-Z-Massage System Button displays red when
activated.
Pressing the Temperature Increase or Decrease
buttons will cause the LED to flash. When it is flashing
you can adjust to the desired temperature setting. If
you hold these buttons down the values will rapidly
increase or decrease. The new and desired tempera-
ture setting will remain on the LED display for 3
seconds to confirm the new value.
Use this button to test if the pump electrical system is
safe. See Pump Test section for details.
When the light flickers, the Power-Saving Timer
function is being set. When the light is on, the
Power-Saving Timer function is set.
Once powered-up the LED displays the current
water temperature automatically.
After 72 hours of operation, the pump will
hibernate and flash “End” with the current water
temperature. When the pump is hibernating both
the heating and water filter functions are
disabled. To re-activate the pump press
lock/unlock button for 3 seconds.
Use this button to set the heating duration and when to
activate the heating system.
This button turns the filter pump on and off.The light
above the Water Filter Button displays red when
activated.
Use this button to activate the heating system. When
the light above the heat button is red, the heating
system is activated. When the light is green, the water is
at the set temperature and the heating system is at rest.
The temperature can be displayed in either Fahrenheit
or Celsius.
1.Press the button and the LED starts to flash.
2.Press the or button to adjust the heating duration, the time
will display in hours.
3.After setting the heating duration, press the button again, the
LED starts to flash. Press the or button to adjust the
estimate time of activation, press button again or without action
for 10 seconds to confirm the setting.The LED maintains.
4.Modify the setting time: Press the button and use the or
button to adjust.
5.Press the button for 2 seconds to cancel the setting.
NOTE:
After setting, the screen shows the current temperature and
time alternately.
NOTE:
Timer adjustment ranges from 0 to 48 hours; Reservation
time adjustment ranges from 0 to 24 hours. If the timer sets at 0
hour means the Timer function is not set.
NOTE:
If the heating system is activated the filtration system will
automatically start.
NOTE:
After turning off the heating system the filtration system will
continue to operate.
NOTE:
The Lay-Z-Massage System will automatically shutoff when
the heater is activated.
NOTE:
The default temperature is 35°C (95°F).
NOTE:
Temperature adjustment ranges from 20°C (68°F) to 40°C
(104°F).
IMPORTANT:
Do not run the Lay-Z-Massage
system when the cover is attached. Air can
accumulate inside the spa and cause
irreparable damage and bodily harm.
RESET BUTTON
IMPORTANT INSTRUCTIONS FOR USING
G
Temperature Adjustment Buttons
Lock/Unlock Button
A
C
Water Filter Button
Celsius/Fahrenheit Toggle
D
Power-Saving Timer Button
B
Heat Button
E
Lay-Z-Massage System Button
F
Test Button
H
I
Power-Saving Timer LED
LED Display
J
NOTE:
The water heat rate may change in the conditions below:
•ΝАСОЧΝЭСОΝШuЭНШШЫΝЭОЦpОЫКЭuЫОΝТЬΝЛОХШаΝ1ő°CΝΧő9°ŻΨ.
•ΝIПΝЭСОΝМШЯОЫΝТЬΝЧШЭΝТЧΝpШЬТЭТШЧΝаСОЧΝЭСОΝСОКЭТЧРΝПuЧМЭТШЧΝТЬΝКМЭТЯКЭОН.
NOTE:
To display the current water temperature, run the filter system
for at least a minute. The water temperature as tested by an external
thermometer may vary from the temperature as displayed on the spa
panel by as much as approximately 2°C.
17
