background image

WARNING

Follow all the Safety and Operating Instructions. If you don’t follow this instructions, it may cause overturn, explode the 
boat and causes to drowning.
  1. Do not exceed the maximum recommended number of persons. Regardless of the number of persons on board, 
      the total weight of persons and equipment must never exceed the maximum recommended load. Always use the 
      seats / seating spaces provided.
  2. When loading the craft, never exceed the maximum recommended load: Always load the craft carefully and 
      distribute loads appropriately to maintain design trim (approximately level). Avoid placing heavy weights high up.
      

NOTE: 

The maximum recommended load includes the weight of all persons onboard, all provisions and personal 

      effects, any equipment not included in the light craft mass, cargo (if any) and all consumable liquids 
      (water, fuel, etc.).
  3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and used at all 
      times.
  4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and air valves, to 
      ensure everything is in good condition and tightly secured. Please stop to repair if you find any damage.
  5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on 
      water.
  6. Passenger numbers and load weights shall by no means exceed specified capacities. Refer to the Technical 
      Specifications section of this manual to determine passenger numbers and load weights for your boat. Overweight 
      will cause overturn and drowning.
  7. Inflate according the numbered air chamber and rated pressure on the boat, or it will cause overinflation and boat 
      explosion. Exceeding the data given on the capacity plate may cause the craft to damage, overturn and lead to 
      drowning.
  8. Keep the boat balanced. Uneven distribution of persons or load in the boat may cause overturn the boat and 
      drowning.
  9. When the boat is in motion, all passengers must remain seated at all times to avoid going overboard.
10. Use the boat in protected shore-zones, up to 300 m (984 feet). Be careful with natural factors such as wind, 
      tidewaters and tidal waves. 

BE AWARE OF OFFSHORE WINDS AND CURRENTS.

11. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may 
      puncture the boat.
12. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other air chamber 
      to prevent the boat from sinking.
13. To avoid damage do not drag the boat on rough surfaces.
14. Don’t leave the boat exposed to sun for long periods of time, as high temperatures shall give rise to air expansion, 
      which can cause irreparable damage.
15. Always wear a lifejacket!
16. It is the responsibility of the owner/operator to have at least on bucket/bailer on board, secured against accidental 
      loss.
17. Never transport the boat in inflated condition on the car. Be aware of the potential harmful effects of liquids such as 
      battery acid, oil, petrol. The liquids may damage your boat.
18. Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of others.
19. Follow these instructions to avoid drowning, paralysis or other serious injuries.
20. Know how to operate a boat. Check in your local area for information and/or training as needed. Inform yourself 
      about local regulations and dangers related to boating and/or other water activities.

SAVE THESE INSTRUCTIONS

Assembling of the boat
NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR PRODUCT AND VOID 
YOUR WARRANTY

1. Spread out the boat on level ground.
2. Assemble the removable fin to the bottom of the boat (Fig.1). Make sure the curvature of the fin is pointed towards the 

back end of the boat.

NOTE: 

Assemble the fin before inflation and also disassemble it after deflation.

NOTE: 

To avoid damage to the removable fin, do not enter shallow water.

3

WARNING: To avoid damage to the boat and injury to passengers, please don’t exceed the 

data given on the builder’s plate.

Technical Specifications

• Inflate the air chambers with a HAND air pump.

An inflation scale is provided with the product.

Inflate the product until the printed scale is charged up to the same level as that of the supplied scale. (refer the 

belowing Table and Illustration)

Caution: 

Under and over-inflation of the boat will result in safety hazards. It is better to check the pressure of the boat 

each time before using. If you use other pressure gauge, the boat pressure should not be more than the data given on 

the builder’s plate.

• Never stand on or rest objects on the boat during inflation.

• Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.

• Extended exposure to sun can shorten the lifespan of your boat. We suggest not leaving boats in direct sunlight for 

more than 1 hour after use.

5. Fold the boat from front to back to remove additional air. You can also use a pump to drain 

any remaining air.

Repair

1. If there is a small puncture, repair it according to the instruction on repair patch.

2. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or 

send the boat to a speciality shop to make the repair.

Registration (For US/Canada customers only)

If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit 

bestwaycorp.com/support to obtain your Certificate of Origin, or you can send e-mail to [email protected] for the 

Certificate of Origin.

The HIN is located on the starboard outboard side of the hull and near the stern.

PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU 

SELL THE CRAFT.

NOTE: All drawings for illustration purpose only. May not reflect actual product.

Storage

1. Keep all accessories for future use.

2. Carefully clean the boat using a mild soap with clean water.

Note: 

Do not use acetone, acid, and/or alkaline solutions.

3. Use a cloth to gently dry all surfaces.

Note: 

Do not dry the product in direct sunlight. Also, never dry with equipment such as electric blowers. Doing so will 

cause damage and shorten the boat’s life span.

4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops together. This will 

prevent damage from occurring to the boat inner structures. Next deflate the floor and seat.

Oars Installation

0.03 bar

0.5 psi

Item

65115

Maximum Number of Persons

1 adult

Maximum Load Capacity

100 kg (220 Ibs.)

Inflated Size

Recommended

Working Pressure

2.75 m x 81 cm

(9' x 32") 

Item

65115

2.75 m x 81 cm (9' x 32")

10 cm

11.5 cm

11.8 cm

Product Inflated Size

Deflated Size

Inflated Size 

Chamber 2

Inflated Size 

Chamber 1

Boat

Components:

• Repair Patch

• Deflation Pipe

Rope x 2

Inflation Scale

Removable Fin 

x 1

Hand Pump

Storage cord x 2

Oar

Oar blade x 2

Shaft x 1

Coupling x 2

Oar ring x 2

Footrest Cushion

Fig. 1

mc

mc

11

12

11

12

13

14

15

OWNER’S MANUAL

Summary of Contents for 65115

































Reviews: