background image

Tongue Edge

LAP Edge

800-245-1577 - Mon - Fri 8AM - 5PM EST

724-866-4357 - After hours and weekends

Email - [email protected]

I

MPORTANT

 I

NFORMATION

 A

BOUT

 Y

OUR

 K

IT

Thank you for purchasing our kit. Please read the following information before beginning construction.
Always check with your local HOA or building code office for any requirements or restrictions.

Tools Required: Hand or Circular Saw

Cordless Drill
Hammer
Pencil

Level
Measuring Tape
6'-8' Ladder(s)

Safety Glasses
Dust Mask
Phillips Screwdriver
Framing Square

Always wear safety glasses when cutting or nailing!

Additional Materials - Not included in kit:

Required: 8' x 7' Garage Door, Vinyl Siding

Shingles or metal roofing, Drip Edge, Roofing Nails or Screws, Paint

Optional: Windows, Walk-in Door, Caulk, Ridge Vent

Floor: Wood flooring is sold optionally. You may choose to build your own or pour a cement pad.

Terminology:

Square - Confirm corners are at 90 degrees
Plumb - Confirm walls and trusses are straight vertically
Wall Plate - Top and bottom 2x4s used to frame walls
Tie Plate - 2x4s connecting wall sections together
Header - Spans top of door opening
OSB - Oriented Strand Board
LAP - Edge of siding that overlaps Tongue
Tongue - Edge of siding that is overlapped

Organize:

Unpack all items & organize according to size and type. This will make items easier to find
when instructed.

Review the parts list on the back page. Should there be missing items or sub-par material
contact Best Barns Customer Service.

DO NOT discard any material including the pallet until your project is complete.

Assembly:

Review all instructions before you begin. Please follow steps carefully and in sequence for
successful results.

If you have any questions we are happy to assist you. Please contact us at:

Primed Soffit Detail

Summary of Contents for Greenbriar II 12x16





















Reviews: