Best Barns Greenbriar II 12x16 Assembly Book Download | Manualshive

Page: 14 / 20

background image

Air
Space

Truss

Shingles

1.

Install a 1x4-6' white pine fascia board against the rear gable trim. Install the fascia so the

bottom edge of the roof sheathing will rest on the edge of the 1x4. See Detail 'E'. Use a straight
edge to align the 1x4 board with the top of the trusses. Use 6d galv. nails.

2.

Install another 6' fascia board. Do not install the last fascia board. This will be applied after

the front overhang is installed.

3.

Repeat on opposite side wall.

Step 14 Install Fascia on Side Walls

Step 15A Install Roof Sheathing

2.

Plumb each truss and gables.

3.

Refer to sheathing layout at the top of the next

page. Install roof sheathing starting at the front
gables lower corner. The roof sheathing should
extend 6-1/4" beyond the 2x3s. Continue to back
wall. Use 6d common spaced 8" apart. The top
row of roof sheathing will be about 1" below
the ridge to allow for optional ventilation.

42-3/8" Long 2x3

Front Gable

1x4 Fascia

2x4 Truss

Roof Sheathing

2x4 Tie Plate

2x4 Soffit Block

Detail 'E'

1x4 -6' Fascia Board

Straight Edge

Nail Fascia to

2x4 Block

6-1/4"

1.

Install (4) four 42-3/8" long 2x3 boards on the

front gable flush with the top of the gable frame.
Use 10d sinkers

«
...
12
13
14
15
16
...
»

Summary of Contents for Greenbriar II 12x16





















Reviews:

No comments

Related manuals for Greenbriar II 12x16

Brand: Palmako Pages: 37

Brand: GARDEN MASTER Pages: 2

Brand: Dancover Pages: 65

Brand: OLT Pages: 47

SS84-SLIDER-METAL-AK

Brand: OLT Pages: 36

Kalle EL18-3422

Brand: Palmako Pages: 52

Brand: Jimmy at work Pages: 13

Brand: Jimmy at work Pages: 15

Brand: Jimmy at work Pages: 25

Brand: Jimmy at work Pages: 33

Brand: Palmako Pages: 34

GARDENSHED Skillion Series

Brand: WAR-LOCK Pages: 23

Brand: Wishbone Pages: 18

Brand: Goodiy Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands