manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual

The BERTHOLD TECHNOLOGIES LB 480 is a cutting-edge laboratory device that is essential for accurate measurements. To ensure proper usage, don't forget to download the user manual for free at manualshive.com. This manual provides detailed instructions on how to operate and maintain this advanced technology.

Share
Download
background image

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

2 – 227

Volume 2

4 Repair, Maintenance and Upkeep

2

4

Repair, Maintenance and 
Upkeep

IMPORTANT

Spare parts for detectors used in the Ex-area must be mounted 
solely by the BERTHOLD TECHNOLOGIES service or by persons 
authorized by BERTHOLD TECHNOLOGIES. If this is not possible, 
you must replace the entire detector or return it to the manufac-
turer for repair.

For devices that are 

NOT

 used in an Ex-area, the following parts 

may be replaced at your own risk and taking into account a loss of 
any existing warranty by BERTHOLD TECHNOLOGIES:

–

the complete detector electronics

–

the complete connection head

–

the crystal at the CrystalSENS

–

the multiplier (PMT)

–

the multiplier crystal combination

–

the detector housing

BERTHOLD TECHNOLOGIES recommends to have detectors 
repaired solely by the BERTHOLD TECHNOLOGIES service or by per-
sons authorized by BERTHOLD TECHNOLOGIES.

Only original spare parts by BERTHOLD TECHNOLOGIES may be 
used.

Please follow the instructions in the Safety Manual (

Volume 1

) and 

the instructions in 

chapter 3

, 

"Electrical Installation", page 2-217

.

After every repair, maintenance or upkeep, please use the check-
lists on 

page 1-51

 and 

page 1-53

.

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LB 480

HANYOUNG NUX RP3 Instruction Manual preview
RP3
Brand: HANYOUNG NUX Pages: 4
jenway 6305 Operating Manual preview
6305
Brand: jenway Pages: 30
National Meter & Automation T200 Manual preview
T200
Brand: National Meter & Automation Pages: 24
Lakeshore 340 Installation Instructions preview
340
Brand: Lakeshore Pages: 2
Kamstrup 382 Manual preview
382
Brand: Kamstrup Pages: 4
OHAUS MC2000 Instruction Manual preview
MC2000
Brand: OHAUS Pages: 84
i-SENS KetoSens User Manual preview
KetoSens
Brand: i-SENS Pages: 50
Landis+Gyr ULTRAHEAT T230 Manual preview
ULTRAHEAT T230
Brand: Landis+Gyr Pages: 26
Landis+Gyr Ultracold T550 Operating Instructions preview
Ultracold T550
Brand: Landis+Gyr Pages: 3
VeEX MPA User Manual preview
MPA
Brand: VeEX Pages: 842
Sage SIP Operation And Instruction Manual preview
SIP
Brand: Sage Pages: 68
Schneeberger MINIRAIL Manual preview
MINIRAIL
Brand: Schneeberger Pages: 35
Kobold DON-05Bx Operating Instructions Manual preview
DON-05Bx
Brand: Kobold Pages: 55
Dennerle Duomat Evolution DeLuxe Instructions For Use Manual preview
Duomat Evolution DeLuxe
Brand: Dennerle Pages: 27
Seaward PAC3760 PLUS Quick Reference Manual preview
PAC3760 PLUS
Brand: Seaward Pages: 2
BYK micro-TRI-gloss ? Operating Instructions Manual preview
micro-TRI-gloss ?
Brand: BYK Pages: 174
LORECa Hearing Instrument PKA87 User Manual preview
PKA87
Brand: LORECa Hearing Instrument Pages: 43
Magnescale SR77 Supplement Manual preview
SR77
Brand: Magnescale Pages: 36

Brands by name

Popular brands

Load more brands