BERNSTEIN 805S Assembly Instructions Manual Download Page 18 | Manualshive

Page: 18 / 23

background image

18

Concealed system 805S

5. Move the float up to increase

or decrease the inflow of water.







6. To clean the water stop, unhook the clamp and unscrew the union nut.

7. Then you can clean the water

stop under running water.

8. Insert the inlet valve. Connect the hose and the shut-off valve. Open the shut-off valve.



«
...
16
17
18
19
20
...
»

Summary of Contents for 805S
























Reviews:

No comments

Related manuals for 805S

Metris Select 2-Spray 73822 1 Series

Brand: Hans Grohe Pages: 24

Brand: MAAX Pages: 16

Brand: Rubi Pages: 28

Brand: Sanela Pages: 5

Finoris 76445 9 Series

Brand: Hans Grohe Pages: 12

ChekPoint EC-3103

Brand: T&S Pages: 35

Metris Select M71 200 1jet sBox 73804 Series

Brand: Hans Grohe Pages: 44

Brand: Drive Pages: 8

SUPRIMO 10.271.033.700

Brand: KWC Pages: 1

Axor Montreux 16520 Series

Brand: Hans Grohe Pages: 8

Brand: identités Pages: 12

Brand: identités Pages: 18

Brand: Victoria + Albert Pages: 8

Brand: Kohler Pages: 12

Brand: Lefroy Brooks Pages: 10

Brand: Bossini Pages: 12

Brand: ERLIT Pages: 17

Brand: MERLYN Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands