BERNHARDT design a.k.a. C-base Instructions Manual Download Page 18 | Manualshive

Page: 18 / 20

BERNHARDT design a.k.a. C-base Instructions Manual Download Page 18

September 2012

a.k.a. c-base

wood veneer modesty panel

IMPORTANT NOTES

Failure to install product according to installation instruction will result in loss of warranty.

Cartons contain all hardware required for assembly.

#8 Wood Screws

C-Base and Wood Veneer Modesty Panel Installation

Illustrations are shown with both the
c-base as well as the optional wood
veneer modesty panel.

Location of wood veneer modesty panel
(Optional).

Mount c-base to underside of top through
the top plate of the base. Locate the base
by the dimensions shown.

To install the wood modesty panel align
the face of the wood veneer panel to the
back or user side of the c-base.  Locate
the panel so that it runs parallel to the
edge of the top and attach it to the
underside of the top with the attached
angle brackets.

Location of wood veneer modesty panel
(Optional).

Mount c-base to underside of top through
the top plate of the base. Locate the base
by the dimensions shown.

To install the wood modesty panel align
the face of the wood veneer panel to the
back or user side of the c-base. Locate
the panel so that it runs parallel to the
edge of the top and attach it to the
underside of the top with the attached
angle brackets.

Wood Veneered
Modesty Panel

36” C-Base

30” C- Base

User side of base

User side of base

Wood Veneer
Modesty Panel

«
...
16
17
18
19
20
»

Summary of Contents for a.k.a. C-base





















Reviews:

No comments