BERNHARDT design a.k.a. C-base Instructions Manual Download Page 10 | Manualshive

Page: 10 / 20

BERNHARDT design a.k.a. C-base Instructions Manual Download Page 10

September 2012

a.k.a. glass run-off desk

IMPORTANT NOTES

Failure to install product according to installation instruction will result in loss of warranty.

Cartons contain all hardware required for assembly.

Machine screws

Glass Run-Off Desk Installation

These illustrations show the assembly
process for installing a glass run-off desk.

Please note that the glass run-off desks
can only be mounted to a workwall
structural rail.

Insert the included aluminum mount
bracket into workwall rail and let it
hang flat.

Press the back edge of the runoff against
the aluminum mount bracket and let it rest
on the horizontal leg.

Align the countersunk holes in the mount
bracket with the tapped holes in the
mount plate.

Thread the provided machine screws into
each hole and tighten.

Be sure runoff is completely secure to
mounting bracket.

Level runoff as needed.

Mount Bracket
And Mount Plate

Leveler

Workwall structure

«
...
8
9
10
11
12
...
»

Summary of Contents for a.k.a. C-base





















Reviews:

No comments