20
BACCG 18V
.......................4500 N
...........................18 V
..........................2,3 kg
..........................2,5 kg
...........................68 dB (A)
...........................79 dB (A)
.......................< 2,5 m/s
2
..........................1,5 m/s
2
TECHNICAL DATA
CAULKING GUN
Feed force ..............................................................................
Battery voltage........................................................................
Weight according EPTA-Procedure 01/2003 (1,5 Ah) ............
Weight according EPTA-Procedure 01/2003 (3,0 Ah) ............
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .......................
Sound power level (Uncertainty K=3dB(A)) ............................
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
....................................................
Uncertainty K= ........................................................................
WARNING
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs),
2006/42/EC, 2004/108/EC and the following harmonized
standards have been used:
EN 60745-1:2009 + A11:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 50581:2012
Künzelsau, 2015-03-16
Armin Hess
Chairman of the Management Board
Authorized to compile the technical fi le
Berner Trading Holding GmbH
Berner Straße 6
D-74653 Künzelsau
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
WARNING! Read all safety warnings and all
instructions.
Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Read and understand the charger operator‘s manual
packaged with your charger.
Always wear goggles when using the machine.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. Your power tool distributor will
normally retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System Berner chargers for charging System
Berner battery packs. Do not use battery packs from other
systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
To reduce the risk of injury, electric shock, and damage to
the tool, never immerse your tool in liquid or allow a liquid
to fl ow inside the tool.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The caulking gun is intended to apply tube or sausage
pack caulks and adhesives to surfaces.In case of doubt,
please read the caulk or adhesive manufacturers‘
instructions.
Do not use this product in any other way as stated for
normal use.
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
ENGLISH
445 369 - Berner-BACCG18V.indd 20
445 369 - Berner-BACCG18V.indd 20
22.07.2015 15:07:21
22.07.2015 15:07:21
