Bergoz MX-BPM User Manual Download Page 33 | Manualshive

Page: 33 / 49

background image

ACCESSORIES (Cont’d)

BPM Chassis BPM-RFC/X

The BPM-RFC/X chassis is built around a 19” Schroff rackable RF chassis.
Dimensions of the bin: 3U x 84F
Schroff reference: Europac Lab HF/RF #20845-283

The BPM-RFC/X is available equipped for 1 up to 16 BPM stations. X being the number of
stations.

BPM-RFC/X with less than 16 stations are partially equipped BPM-RFC/16. As a result, all
BPM chassis are field-upgradable to the full 16-station chassis.

Chassis rear view

DB9 male External commands input connector. Common to all stations

SMA jack RF input for test station

IEC male connector for AC mains

DB15 female BPM station output connector, one per BPM station

SMA jack A to D button inputs, 4 per BPM station, A on top

BERGOZ Instrumentation

Multiplexed

01630 Saint Genis Pouilly, France

Beam Position Monitor

Tel. +33-450.426.642
Fax +33-450.426.643

Page 31

User’s manual

BERGOZ Instrumentation - 01630 Saint Genis Pouilly, France - Tel.: +33-450.426.642 - Fax: +33-450.426.643

email: [email protected] - http://www.bergoz.com - Registre des Métiers: Bourg-en-Bresse - Registre des ingénieurs: Zurich

TVA-VAT-IVA-USt. Nº FR88414997130 - Sàrl. capital 152K - Siren 414 997 130 R.C.S. Bourg - APE 332B

«
...
31
32
33
34
35
...
»

Summary of Contents for MX-BPM


















































Reviews:

No comments

Related manuals for MX-BPM

Brand: THORLABS Pages: 20

Flow-Tek FTG Series

Brand: Bray Pages: 11

Brand: Bray Pages: 12

ABL1000WB Series

Brand: Aerotech Pages: 40

Brand: Aerotech Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands