background image

4

GENERAL

1  GENERAL SAFETY INFORMATION

 

b

Check that the product is complete, undamaged and 

as ordered as soon as you receive it. Report any dis-

crepancies or damage to the 

B

 dealer who sold 

it.

 

b

This product must be installed by a legally qualified 

heating engineer. On completion of the installation, 

the installer must issue the owner with a declaration 

of conformity confirming that the installation has been 

completed to the highest standards in compliance 

with the instructions provided by 

B

 in this instruc-

tion manual, and that it conforms to all applicable 

laws and standards.

 

b

This product must only be used for the purpose 

for which it is designed and made, as specified by 

B

B

 declines all responsibility, contractual or 

other, for damage to property or injury to persons or 

animals caused by improper installation, adjustment, 

maintenance or use.

 

b

The product must be serviced at least once a year. 

Servicing must be arranged in advance with the 

B

 Technical Assistance Centre.

 

b

All servicing and repairs must be performed by a 

qualified heating engineer.

 

b

If water leaks from the storage cylinder, turn off the 

water supply and contact 

B

’s Technical Assis-

tance Centre or a qualified heating engineer imme-

diately.

 

b

If the solar storage cylinder is not going to be used for 

an extended period of time, contact the manufactur-

er’s  Technical Assistance Centre to have at least the 

following operations performed:

 -Close the shut-off cocks for the domestic hot water 

circuit

 -Shut down the boiler connected to the storage cylin-

der as instructed in its own manual

 -Switch the storage cylinder OFF at the control panel 

(if fitted) and at the mains power switch

 -Drain the central heating circuit and domestic hot 

water circuit if there is any risk of freezing.

 

b

Anti-freeze (propylene glycol) is available separately 

and must be mixed with water in a percentage vary-

ing from 30% to 50% as instructed in the installation 

and maintenance manual for the 

B

 solar collec-

tors.

 

b

Only fill the solar collector (primary) circuit with water 

and glycol premixed in the percentages specified in 

the 

B

 installation and maintenance manual.

 

b

This instruction manual is an integral part of the prod-

uct. It must be kept safe and must ALWAYS accom-

pany the product, even if it is sold to another owner or 

transferred to another user or to another installation. 

If you lose this manual, order a replacement imme-

diately.

2  PRECAUTIONS

The operation of any appliance that uses electrical power 

demands that a number of fundamental safety precautions 

be respected. In particular:

 

a

Never attempt to install the system without using suit-

able personal protection equipment and without fol-

lowing all applicable occupational safety standards.

 

a

Do not touch the storage cylinder when barefoot or 

wet if it has any electrical accessories connected to 

it.

 

a

Never clean or service the storage cylinder without 

first turning the mains power switch OFF to discon-

nect all electrical accessories (if fitted) from the mains 

electricity supply.

 

a

Never pull, disconnect, or twist any electrical cables 

coming from the appliance even if it is disconnected 

from the mains electricity supply.

 

a

Do not expose the storage cylinder to the elements. It 

is not designed for use outdoors.

 

a

If the pressure in the solar collector circuit drops, do 

not top up with water alone, since this increases the 

risk of damage from freezing.

 

a

Do not use connections or safety devices or fittings 

(expansion vessels, pipes, insulation) that are not 

specifically designed and tested for use in solar wa-

ter heating systems.

 

a

Do not allow children or infirm persons to operate the 

system unsupervised.

 

a

Do not dispose of packaging material into the envi-

ronment, or leave it within the reach of children, since 

it can become a potential hazard. Dispose of packag-

ing material in compliance with applicable legislation.

General

Summary of Contents for IDRA MS 150 LE





















Reviews: