background image

14

TECHNICAL ASSISTANCE CENTRE

15  PUTTING INTO SERVICE

It is essential to perform the following checks before start-

ing up or testing the functioning of the storage cylinder. In 

particular, check that:

-  The  supply  cocks  in  the  domestic  water  circuit  are 

all open

-  The water connections to the boiler and solar collec-

tors have been made correctly

-  All the pipes in the water circuit have been insulated 

in conformity to relevant standards

-  The electrical connections of all accessories have 

been made correctly

-  The solar collector circuit has been correctly flushed 

out  and  filled  with  water-glycol  mix,  and  all  air  has 

been bled out of the circuit (see the manual for the 

solar collectors)

-  Start up the boiler (if installed) as instructed in its own 

manual.

-  Put the solar collectors into service. See the manuals 

for the solar collectors and associated accessories.

Once the system has been started up, perform the follow-

ing checks.

-  Make sure that all pumps are free and rotate in the 

right direction

-  Make sure that all circuits have been bled.

-  Make  sure  that  the  boiler  and  solar  collectors  con-

nected to the system shut down correctly when their 

mains power switches are turned OFF.

Provided the above checks have been completed satisfac-

torily, restart the system and verify its performance.

16  TEMPORARY SHUTDOWN

If you are going away for a short period of time like a week-

end or a short holiday, etc., and outdoor temperatures are 

going to remain above ZERO, proceed as follows.

-  Adjust the storage cylinder thermostat to its minimum 

setting.

If the temperature to which the heater is exposed can 

fall below 0°C (frost hazard), perform the operations 

described in paragraph "Shutdown for extended pe-

riods".

17  PREPARING FOR EXTENDED 

PERIODS OF DISUSE

If the storage cylinder is not going to be used for an extend-

ed period of time, perform the following operations:

-  Switch the electricity supply to the storage cylinder’s 

valve group and to any associated boiler OFF at the 

main switch and at the control panel

-  Close the shut-off cocks for the domestic hot water 

circuit.

Drain the central heating circuit and domestic hot wa-

ter circuit if there is any risk of freezing.

Technical Assistance Centre

Summary of Contents for 20086803





















Reviews: