background image

General Features

New ergonomic design

Large backlighted display, 2 lines, 16 columns

Brightness and Contrast adjustment

Backlighted keys

3 pairs of keys for fast activation of Burglar, Fire
and Emergency alarms

2 Tamper Switches

1 Snatch Switch (optional)

1 Programmable zone

Choice of Wall Anchorage

Description

The MIA-S keypad has been designed to be used
with compatible Omnia and Academy40 series Con-
trol panels.
The operating principles of the MIA-S and OmniaTAST-
R keypads are the same, barring the differences de-
scribed in this Instructions Insert. Therefore, please
review the Control panel manual to get an overall
understanding.

Installation Guidelines

Carefully work through the following steps (see Fig-
ure 1)

1. Open the flip 

14

.

2. Remove the screws 

15

.

3. Remove the frontplate 

16

.

4. Detach the PCB 

11

 from the backplate 

12

.

5. Insert the Snatch Switch 

2

 as per Figure 1 (for

keypads with Snatch Switches only).

The Snatch Switch is optional (order code ASNC).

6. Pull the connection wires through the wire entry

13

.

7. Using wall anchors, secure the backplate 

12

 to

the wall or onto the outlet box.

8. Secure the Snatch bracket 

1

 to the wall (for

keypads with Snatch Switches only).

The Snatch Switch cannot be used when mount-
ing the MIA-S onto an outlet box

9. Reattach the PCB 

11

 to the backplate 

12

.

10. Connect the Snatch switch 

2

 to the connector 

5

(for keypads with Snatch Switches).

11. Set the BPI Level, as per the relevant instructions

in the Control panel manual.

12. Assign the Address, as per the relevant instruc-

tions in the Control panel manual.

13. Complete the connections on the terminal board

10

, as per the relevant instructions in the Control

panel manual.

14. Replace the Cover 

16

 to the backplate 

12

.

15. Using the screws 

15

 secure the Cover.

Setting the BPI Level

The BPI Level of the keypad must match the BPI
Level of the Control panel (please refer to your
Control panel manual for details).

The BPI Level of Omnia and Academy40 se-
ries Control panels is 5 V.

Using jumpers 

3

 and 

9

, as per Table 1, select the

keypad BPI Level.

-8 

 

:/

:/

   

 

   

 

Assigning the Address

Each keypad must occupy a different Address.
Using the DIP switches 

6, 

as per Table 2, assign

the keypad Address.

The positions of DIP switches no. 1 and no. 2
are irrelevant.

,-8

,!&--

 -< $=&-

(

(

)

*

+

ENGLISH

Summary of Contents for MIA-S









Reviews: