IC Statement
Radia5on Exposure Statement:
This equipment complies with IC radia5on exposure limits set forth for an uncontrolled environ-‐
ment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Déclara5on d'exposi5on aux radia5ons:Cet équipement est conforme aux limites d'exposi5on aux
rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé
et u5lisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following condi5ons: (For module de-‐
vice use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The er module may not be co-‐located with any other er or antenna.
As long as 2 condi5ons above are met, further er test will not be required. However, the
OEM integrator is s5ll responsible for tes5ng their end-‐product for any addi5onal compliance re-‐
quirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les condi5ons suivantes: (Pour
u5lisa5on de disposi5f module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'an-‐
tenne et les u5lisateurs, et2) Le module éme+eur peut ne pas être coïmplanté avec un autre
éme+eur ou antenne.
Tant que les 2 condi5ons ci-‐dessus sont remplies, des essais supplémentaires sur l'éme+eur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son
produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these condi5ons can not be met (for example certain laptop configura5ons or co-‐
loca5on with another er), then the Canada authoriza5on is no longer considered valid
and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-‐evalua5ng the end product (including the er) and obtaining a sepa-‐
rate Canada authoriza5on.
NOTE IMPORTANTE:Dans le cas où ces condi5ons ne peuvent être sa5sfaites (par exemple pour
certaines configura5ons d'ordinateur portable ou de certaines co-‐localisa5on avec un autre émet-‐
teur), l'autorisa5on du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être u5lisé
sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit
final (y compris l'éme+eur) et l'obten5on d'une autorisa5on dis5ncte au Canada.
End Product Labeling
This er module is authorized only for use in device where the antenna may be installed
公司
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible
de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module device
use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna
.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator
is still responsible for testing their end-product for any additional compliance requirements required with this
module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour
utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les
utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas
nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes
exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with
another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used
on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus
considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances,
l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation
distincte au Canada.