FCC Statement
This er must not be co-‐located or opera5ng in conjunc5on with any other antenna or
er.
Opera5ons in the 5.15-‐5.25GHz band are restricted to indoor usage only.
Radia5on Exposure Statement:
This equipment complies with FCC radia5on exposure limits set forth for an uncontrolled envi-‐
ronment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
This device is intended only for OEM integrators under the following condi5ons:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The er module may not be co-‐located with any other er or antenna.
3) Module approval valid only when the module is installed in the tested host or compa5ble se-‐
ries of host
As long as 3 condi5ons above are met, further er test will not be required. However, the
OEM integrator is s5ll responsible for tes5ng their end-‐product for any addi5onal compliance re-‐
quirements required with this module installed
IMPORTANT NOTE: In the event that these condi5ons can not be met (for example certain laptop
configura5ons or co-‐loca5on with another er), then the FCC authoriza5on is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-‐evalua5ng the end product (including the er)
and obtaining a separate FCC authoriza5on.
End Product Labeling
This er module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must
be labeled in a visible area with the following: “Contains FCC ID: JVPRX”. The grantee's FCC ID can
be used only when all FCC compliance requirements are met.
Manual Informa5on To the End User
The OEM integrator has to be aware not to provide informa5on to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory informa5on/warning as show in this
manual.
公司
as 2
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements required with this module
installed
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID
can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm
may be maintained between the antenna and users. The final end product must be labeled in a visible area with
the following: “Contains FCC ID:
JVPRX
”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met
.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove
this RF module in the user's manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
