![background image](http://html1.mh-extra.com/html/benq/mx613st/mx613st_product-service-manual_2734828007.webp)
7
2.17 Color Wheel Segment
R80Y30W60C30B75G85
2.18 Color Wheel Speed
50HZ 2X 60H 2X
3.Optical Specification
Test under 60” (diagonal) image size with Wide projection lens position.
3.1 ANSI Brightness
Normal: Typical 2250 lm(For reference)
Minimum 2000 lm
ECO: Typical 1800 lm(For reference)
Minimum 1600 lm (For reference)
3.2 ANSI uniformity
Minimum 55%
3.3 JBMA Uniformity Minimum
70%
3.4 ANSI Contrast
Minimum 150:1
3.5 FOFO Contrast
Minimum 1600:1
3.7 FOFO Contrast with DB
N.A.
3.8 Focus Quality
3.8.1
区
Pattern
(1) If pattern can be uniformly focused – not worse than limit
sample – then pass!
Limit Sample: Mercury Projector, S/N: 282596-00128
(2) If it’s difficult to judge, then check 3.8.2
3.8.2
R
G
B
Defocus (Maximum)
3.0
3.0 3.0
Flare (Maximum)
4.0
4.0 4.0
3.9 Focus unbalance
Max. 50cm
3.10 Color Coordinate
(Confirm at PVT stage)
Color
x
y
White
0.311±0.04 0.356±0.04
Red
0.631±0.04 0.357±0.04
Green
0.339±0.04 0.570±0.04
Blue
0.147±0.03 0.075±0.03
3.11 Color Uniformity
(Confirm at PVT stage)
Color
△
uv
White
≦
0.02
Red
≦
0.02
Green
≦
0.02
Blue
≦
0.02
3.12 Color Gamut(Compare to
NTSC)
Typical 60%
3.13 Light Leakage in AA
△≦
0.5 lux compared with center point @ full black pattern
within 60” (Diagonal at 1.1m).
This light-leakage is only described as the spot light with
obvious shape. The uniformity difference of black pattern is
not included.
3.14 Light Leakage out of AA
≦
0.5 lux, @ full black pattern with 60~80“(Diagonal at 1.1m)
(Except DMD Defect)
3.15 Ghost
Ghost Contrast > (Confirm at EVT2 stage)
3.16 Lens Shift Speed(sec)
(only for motorized len shift)
N.A.
3.17 Defect (Color Band, Dark
Corner, Dark band)
Follow limited sample (When needed).
4.Lamp Specification
4.1 Lamp
Philips 210W-170W 0.9 E20.9 LL FusionStar Lamp
4.2 Lamp Sync Type
AC Lamp
4.3 Lamp Flick
Follow limited sample (When needed).
4.4 Lamp Power
Normal Mode
210W
Summary of Contents for MX613ST
