BenQ MX613ST, Product Service Manual

Page: 37 / 124

37
Blemish around the logo must be equal or smaller than 0.05 mm
2
1.3 表面气泡 — 不可有。
Bubble on the surface is to be reject.
TABLE 2 :
产品一般外观的塑料件检验标准 (General Product of plastic outlook inspection standard)
NO Appearance Spec
1 缩水
Shrinkage
A
区
:
不可有缩水
,
以带手套检验
,
手摸过去不可有凹
陷的感觉
A region: No Shrink. With gloves, no feeling of sink when touching the surface
B / C
区
:
不能明显看出
B/C region: not obvious
2 流痕
,
咬
花 , 光泽
Run,
Texture,
Gloss
不能有明显的深浅不均
No obvious non-uniformity
3 接合线
Welding
Line/Knit
Line
用指甲划过不会有停顿感
,
并附近无明显之光泽差异
When scratching on it, there’s no feeling of obstruction. Also, there should not be obvious
difference in gloss nearby it.
4 顶白
Ejector
Mark
不可
Reject
5 Label/screw
s shortage
不允许
Reject
6
缺料
Material
shortage
缺料不可影响机构强度和表面
Material shortage is not allowed to impact structure strength and surface
7 色差
Chromatic
aberration
喷漆 (Painting):
Δ
E<=2; L<=1.5 ;
Δ
A,B <= 0.6
银粉漆
(Paint, aluminum).
Δ
E<=2 L<=1.0;
Δ
A, B <= 0.6
非银粉漆 (Paint, non-aluminum)
素材
(Raw material) :
Δ
L,A,B<=0.6 ,
Δ
E<=0.75
8 印刷
Printing
文字印刷不得有漏印、断线、重影、组细不均、溢墨、印偏
( 1mm )
、印斜
(
歪斜＜
0.3
mm ) 。
Printing must not have incomplete printing, break off, overlap, uneven thickness,
excessive ink, printing misalignment (1mm), printing slanting & crooked
(<0.3mm)
文字印刷颜色须确认是否正确 。
Printing color must be comparable to color chip and sample.
9 Logo of
panel
sticker
文字印刷不得有漏印
.
断线
.
重影
.
组细不均
.
溢墨
.
印偏
( 1mm)
印斜
(
歪斜 ＜
0.5 mm).
Printing must not have incomplete printing, break off, overlap, uneven thickness, excessive
ink, printing misalignment (1mm), printing slanting & crooked (<0.5mm)
文字印刷颜色须确认是否正确
.
Printing color must be comparable to color chip and sample.
10
刮伤
Scratch/Nic
ks
Side A:
(W < 0.1mm , L < 3mm):
容许 2 个
Only 1 this kind of scratch is accepted
W < 0.1mm , L < 3-5mm
容许
1
个
No this kind of scratch is accepted
Side B:
W < 0.15mm , L < 3mm
容许
3
个
Only less than 2 this kind of scratch is accepted
W < 0.15mm , L < 3-5mm
容许
2
个
Only 1 this kind of scratch is accepted
Side C: