background image

  7

  Introduction

Introduction

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, 
please contact your place of purchase.

Standard accessories

Optional accessories

Replacing the remote control batteries

1.  Press and open the battery cover, as illustrated.
2.  Remove the old batteries (if applicable) and install two 

AAA batteries. Make sure that the positive and negative 
ends are positioned correctly, as illustrated.

3.  Replace the battery cover until it clicks into place.

Projector

Remote control with 

batteries

VGA cable

Quick start guide

Warranty card*

Power cord

• The supplied accessories will be suitable for your region, and may differ from those illustrated.
• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

1.  Spare lamp kit
2.  3D glasses

3.  Dust filter

• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, 

bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for 

your region.

• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the 

batteries to avoid damage to the remote control from possible battery leakage.

Digital Projector

Quick Start Guide

Summary of Contents for MS550P













































Reviews: