manualshive.com logo in svg

BenQ GH680, User Manual

Share
Download
BenQ GH680 User Manual Download Page 3

Eng

lish

Federal communication commission interference 
statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

This equipment has been tasted and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no guarantee that interference will 
not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

• consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or 
transmitter.

Keep your camera away from sharp objects and avoid 
collision. 

When the camera is not in use, please place it in the pouch 
and a steady place. Plus, always keep your camera away 
from pressure to avoid possible damage.

Summary of Contents for GH680









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands