Benelli BN125 2018 Owner'S Manual Download Page 23

Page: 23 / 75

3 - 7

Instrument and control functions

Brake lever

The brake lever is located on the right side

of the handlebar. To apply the front bra-

ke, pull the lever toward the throttle grip.

The brake lever has a position adjustment

knob.

1. Brake lever

2. Distance between brake lever and

throttle grip

3. Brake lever position adjusting knob

4. “

→

” mark

To adjust the distance between the brake

lever and the accelerator dial, turn the

knob clockwise or anticlockwise; anti-

clockwise will move the lever closer, while

clockwise will move it further away. Make

sure that the correct adjustment, set from

the adjustment gauge is in line with the

brake lever reference “

→

”.

Brake pedal

The brake pedal is located on the right

side of the motorcycle. To apply the rear

brake, press down on the brake pedal.

MUMBN125MY17.indb 7

05/04/2018 14:26:54

Summary of Contents for BN125 2018












































































Search results

Summary of Contents for BN125 2018

Reviews:

Related manuals for BN125 2018

Brands by name

Popular brands

Benelli BN125 2018, Owner'S Manual

Search results

Summary of Contents for BN125 2018

Reviews:

Related manuals for BN125 2018

Brands by name

Popular brands