BENE P2 Safety And Operating Instructions Manual Download Page 5

5

SAFETY INSTRUCTIONS

 

Please observe the safety instructions! 

  Improper operation of the system may 

  result in personal injury and cause 

  damage to objects!

1.    Unplug the power cord in case of smoke,  

  smell or unusual noise. 

2.    Make sure no objects or parts of the body 

  get caught when operating the motor. 

3.    The piece of furniture must not be 

  adjusted in height if other people are 

  located directlyin its vicinity. 

4.    Do not place any objects or parts of the 

  body between fixed or movable parts. 

5.    Height adjustment is only possible in jog 

  mode. If an obstacle is encountered or if 

  there is a functional fault, stop the  

  adjustment immediately. 

6.    Make sure adjacent objects are placed at 

  a minimum distance of 25 mm to prevent 

  them from being squeezed or sheared. 

7.    Ensure that the safety distances are 25 

  mm for movable parts (this also applies 

  for organisational elements which are 

  fitted above or underneath the furniture, 

  mounted to adjoining walls or building 

  parts such as open windows). 

8.    The protection against uncontrolled move- 

  ment does not prevent objects being 

  trapped! For physical reasons, „soft“ 

  obstacles are not easily recognised and 

  evaluated, if at all. 

9.    In case of hitting an obstacle, slight  

  damage (scratching) to such obstacles 

  may result (table is lifted at nominalspeed). 

10. Do not change or modify the control 

  mechanism or the operating device. 

11. Never open the enclosure of the control 

  unit or power supply. Unauthorised ope- 

  ning of the enclosure or improper repairs 

  may endanger the user and voids all 

  warranty claims.

 

Summary of Contents for P2













Reviews: