background image

 

MD-6XP Mid-Rise Scissor Lift 

21

 

P/N 5900108 — Rev. F — March 2020 

Fill the Hydraulic Fluid Reservoir 

The Hydraulic Fluid Reservoir on the Power Unit must be filled with Hydraulic Fluid or automatic 

transmission fluid before you begin normal operation. 
The Hydraulic Fluid Reservoir holds approximately 

1.5 gallons / 5.5 liters

The Power Unit will 

not

 work correctly until the reservoir is filled with approved Hydraulic Fluid. 

Approved Hydraulic Fluids are any general purpose ISO-32, ISO-46, or ISO-68 hydraulic oil or 

approved automatic transmission fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, Shell 

Tellus S4 / S3 / S2, or any synthetic multi-vehicle automatic transmission fluid. 

 WARNING 

Do not run the Power Unit without Hydraulic Fluid; you will damage it. 

To fill the Hydraulic Fluid Reservoir

1.

 

Remove the Reservoir Cap from the top of the Hydraulic Fluid Reservoir. 
Take care to 

keep contaminants out

 of the Hydraulic Fluid Reservoir. 

2.

 

Add the required amount of Hydraulic Fluid to the Reservoir. 

3.

 

If the Reservoir is low, add approved fluid until the fluid level is at least at the minimum level; 
maximum level is best. 
If your Reservoir does not have the MAX/MIN markings, full is approximately .5 in / 12.5 mm under 

the Reservoir Cap. 

4.

 

When the Reservoir is filled, put the Reservoir Cap back on. 

 

 

Summary of Contents for MD-6XP













































Reviews: