BendPak MD-6XP Installation And Operation Manual Download Page 23 | Manualshive

Page: 23 / 44

background image

MD-6XP Mid-Rise Scissor Lift

23

P/N 5900108 — Rev. F — March 2020

Install a Thermal Disconnect Switch

⚠

WARNING

The motor on the Power Unit supplied with your Lift has no thermal overload
protection.

Have the Electrician connect a motor Thermal Disconnect Switch or overload device that will make

sure the equipment shuts down in the event of an overload or an overheated motor.

⚠

DANGER

Installing a Thermal Disconnect Switch

must

be performed by a licensed, certified

Electrician. Do not perform

any

maintenance or installation on the Lift without first

making sure that main electrical power has been disconnected from the Lift and

cannot

be re-energized until all procedures are complete.

High running amps that exceed the motor’s full load amps (FLA) rating may result in permanent

damage to the motor.
BendPak strongly recommends you

not

exceed the rated duty cycle of the motor.

«
...
21
22
23
24
25
...
»

Summary of Contents for MD-6XP













































Reviews:

No comments

Related manuals for MD-6XP

Brand: Skyjack Pages: 213

Brand: Dato Pages: 29

Brand: Oshkosh Corporation Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands