BendPak HDS-18E, Installation And Operation Manual

Page: 9 / 56

9
FLOOR PLAN
*IMPORTANT NOTE*
Check Diagonal Measurements
To Ensure Square Layout - Diagonal Measurements Must Be Equal.
MODEL HDS-18E HDS-27 HDS-27X
Lifting Capacity* 18,000 lbs. / 8165 Kg. 27,000 lbs. / 12,247 Kg. 27,000 lbs. / 12,247 Kg.
*Max Capacity / Front Axle 9,000 lbs. / 4082 Kg. 13,500 lbs. / 6,124 Kg. 13,500 lbs. / 6,124 Kg.
*Max Capacity / Rear Axle 9,000 lbs. / 4082 Kg. 13,500 lbs. / 6,124 Kg. 13,500 lbs. / 6,124 Kg.
A -Overall Width 153-1/2” / 3899 mm 153-1/2” / 3899 mm 153-1/2” / 3899 mm
B -Outside Length 257” / 6528 mm 257” / 6528 mm 317” / 8052 mm
C -Overall Length 309-1/4” / 7856 mm 312-1/2” / 7940 mm 376-3/4” / 9569 mm
D -Height of Columns 91-1/4” / 2318 mm 91-1/4” / 2318 mm 91-1/4” / 2318 mm
E -Min. Runway Height 8-1/2” / 216 mm 9-1/2” / 240 mm 9-1/2” / 240 mm
F -Max. Rise 60” / 1526 mm 60” / 1524 mm 60” / 1524 mm
G -Max. Lifting Height 69-1/2” / 1766 mm 69-1/2” / 1764 mm 69-1/2” / 1764 mm
H -Width Between Columns 133-1/2” / 3391 mm 133-1/2” / 3391 mm 133-1/2” / 3391 mm
I -Runway Width 22” / 559 mm 22” / 559 mm 22” / 559 mm
J -Width Between Runways (*) MIN 40” / 1016 mm 40” / 1016 mm 40” / 1016 mm
J -Width Between Runways (*) MAX 45-1/4” / 1427 mm 45-1/4” / 1149 mm 45-1/4” / 1149 mm
K -Runway Centerline (*) MIN 67” / 1702 mm 67” / 1702 mm 67” / 1702 mm
K -Runway Centerline (*) MAX 72-1/4” / 1835 mm 72-1/4” / 1835 mm 72-1/4” / 1835 mm
L -Outside Edge of Runways (*) MIN 89” / 2261 mm 89” / 2261 mm 89” / 2261 mm
L -Outside Edge of Runways (*) MAX 94-1/4” / 2394 mm 94-1/4” / 2394 mm 94-1/4” / 2394 mm
M -Drive-Thru-Clearance 109” / 2769 mm 109” / 2769 mm 109” / 2769 mm
N -Length of Runways 257” / 6528 mm 256-1/2” / 6520 mm 318-3/4” / 8098 mm
Min. Wheelbase @ Rated Capacity 185” / 4699 mm 185” / 4699 mm 230” / 5842 mm
Min. Wheelbase @ 75% Capacity 160” / 4064 mm 160” / 4064 mm 195” / 4953 mm
Min. Wheelbase @ 50% Capacity 135” / 3429 mm 135” / 3429 mm 165” / 4191 mm
Min. Wheelbase @ 25% Capacity 110” / 2794 mm 110” / 2794 mm 130” / 3302 mm
Locking Positions 13 13 13
Lock Spacing Every 4” / 100 mm Every 4” / 100 mm Every 4” / 100 mm
Lifting Time 75 Seconds 75 Seconds 75 Seconds
Standard Motor (**) 220 VAC / 60 Hz. 1Ph. 220 VAC / 60 Hz. 1Ph. 220 VAC / 60 Hz. 1Ph.
Emission sound pressure at Operator Position < 70 dB(A)
* This dimension may be limited with the addition of rolling jacks. See Rolling Jack Specifications on Separate page.
** For CE compliant countries see errata sheet included with control panel.
The design, material and specifications are subject to change without notice.