BendPak HD-12-B Installation And Operation Manual Download Page 36

Page: 36 / 44

LIFT WILL NOT STAY UP

POSSIBLE CAUSE

1. Air in oil, (1,2,3)
2.

Check valve leaks, (6)

3.  Cylinders leak internally, (7)
4.  Lowering valve leaks, (4,5,1,7,6)
5.  Leaking fittings, (8)

REMEDY

INSTRUCTION

1. Check oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .The oil level should be up to the bleed screw in the

reservoir with the lift all the way down.

2. Oil seal damaged and cocked . . . . . . . . . . . . . . . . . . . . . . . . Replace oil seal around pump shaft.

3. Bleed cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to Installation Manual.

4. Flush release valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hold release handle down and start unit allowing it to

run for 15 seconds.

5. Replace with new valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replace with new valve.

6. Return unit for repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return unit for repair.

7. See Installation Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Consult Lift Manufacturer.

8. Check complete hydraulic system for leaks. . . . . . . . . . . . . . . Tighten all hydraulics fittings and inspect all hoses.

Summary of Contents for HD-12-B













































Search results

Summary of Contents for HD-12-B

Reviews:

Related manuals for HD-12-B

Brands by name

Popular brands

BendPak HD-12-B, Installation And Operation Manual

Search results

Summary of Contents for HD-12-B

Reviews:

Related manuals for HD-12-B

Brands by name

Popular brands