S.p.A.
S.p.A.
S.p.A.
S.p.A.
BL 105
4
PACKING AND TRANSPORT
◊
WIDTH: 87 cm.
◊
HEIGHT: 50 cm.
◊
LENGTH: 72 cm.
-PICT. n°2-
•
Remove the power hoe from its packing
•
Accurately clean cutters hubs and cutters supporting shaft applying a small quantity of
grease in order to make assembly and future removal easier.
•
Fit the two cutters blades with the dust protection ring on the cutters supporting shaft,
then insert cutters blades in second and third position along the length of 90 cm or 120
cm.
•
Pay attention to cutters blades cutting edge direction, as there is a right side and a left
side for any position.
•
Insert side disks in the hexagonal hole and block the cutters using the through pin (with a
length variable according to the cutters width) inserting on the other side the washer and screwing the nut M14. The cutters tie
pin must always be introduced from the right side (right side from driving position), in order to avoid fastening nut unscrewing
during machine running. See PICT. 2
•
Fit the rear spur already connected with the arm, on the rear part of cutters crankcase support, using the pin and the special
spring.
•
Fit the handlebar on the support with the full-side adjustment (rack, wheel system) is fitted with a single pin on the hand lever.
•
Fit transmission rod on the lever coming out from left side of transmission, blocking it with the rapid fastening device pre-fitted
on the lever and relative split pin.
•
In the version with electric start the battery must be made operative.
•
STEPS TO FILL AND CHARGE THE BATTERY (for versions with electric start engine)
IMPORTANT: in the battery of a packed brand-new machine there isn’t any liquid
. To make the battery functional you
have to add the liquid furnished together with the battery.
1)
Remove the sheet cover (Picture 13, ref.” N”) by unscrewing the fin nuts Picture 13, ref. “R”.
2)
Remove the 6 caps from the battery or remove the rubber strip covering the holes.
3)
Take the bottle containing the liquid (Picture 14) and place it on the holes of the battery in order to empty its content into the battery.
4)
Charge the battery by means of a charger for at least 6 hours at 12 volt tension after having disconnected the red cable from the +
pole of the battery, Picture 15, ref. “U”, leaving the holes open.
5)
Disconnect the charger and put again the 6 caps or the rubber strip covering the holes.
6)
Reconnect the red cable Picture 15, ref. “U” to the + pole of the battery.
7)
Replace the sheet cover Picture 13, ref. “N” and fix it with the fin nuts.
TECHNICAL FEATURES OF THE BATTERY: MODEL 12 V 18°A h
IMPORTANT: Before using the power-hoe, remove the plastic cap over the gearbox
breather cap, which has been fitted to prevent oil from leaking during machine packing.
SAFETY RULES AND LIMITS ON USE
-PICT. n°3-
•
Please read carefully the operation and maintenance manual supplied with the machine.
•
The use of the machine is forbidden to persons younger than 16 years.
•
The operator is responsible of any possible damage and he should always drive the machine carefully
and safety.
•
Person unfamiliar with the machine and have never used it are obliged to read first the operation and
maintenance manual.
•
Before carrying the machine always empty the fuel tank.
•
Before leaving the machine be sure that it is fully stopped.
•
Never use the machine without heavy shoes and long transfers. Always inspect the area where you
want to work taking off stones, branches, cables and any other thing which can be dangerous.
•
Before start working, make sure that a radius of minimum 5 mt. is completely free.
•
Clean any possible leakage of fuel.
•
Fill up when the engine is off and not hot, always in an open space far from fires or any heating source
and refrain from smoking during this operation.
•
Before starting the machine make sure that you can quickly stop the engine and that you are familiar
with the control levers.
•
Never allow the engine to run in enclosed spaces where the highly toxic carbon monoxide could not
evacuate.
•
Never start or use the machine not completely assembled especially concerning the safety devices
and the tiller protection guards which should always be completely assembled with all its extensions.
•
Never fix or clean the tiller blades or any other tools when the engine is running.
•
Never work in over 30% sloping ground.
•
We are not responsible for accidents due to the wrong use of the machine neglecting the above basic instructions.