background image

FCC Regulatory Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-

tions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer-

ence received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

- Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment.

RF Exposure Compliance

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-

ment. This transmitter must not be co-located or operating in conjunction with any other antenna or 

transmitter.

30

29

ISED Regulatory Compliance

This device contains licence-exempt transmitter that comply with Innovation, Science and Economic 

Development Canada’s licence-exempt RSS(s). 

Operation is subject to the following two conditions:

This device may not cause interference.

This device must accept any interference, including interference that may cause undesired operation 

of the device.

L’émetteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, 

Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. 

L’exploitation est autorisée aux deux conditions suivantes:

L’appareil ne doit pas produire de brouillage;

L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible 

d’en compromettre le fonctionnement.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled envi-

ronment. This transmitter must not be co-located or operating in conjunction with any other antenna 

or transmitter.

Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un 

environnement non contrôlé. Cet émetteur ne doit pas être situé ou fonctionner conjointement avec 

une autre antenne ou un autre émetteur.

CAN ICES-3 (B)/NMB-3(B)

Summary of Contents for Mabot



















Reviews: