Bellfires VIEW BELL TOPSHAM 3 LF Installation Instructions & Manual For Maintenance Download Page 44

Page: 44 / 76

English

Installation instructions

Keep the burner oriﬁ ces unblocked

Figure 27: Marble pebbles Vertical Bell Small Tunnel 3 CF/LF

Position natural gas and propane/butane burner

Important:

•

Do not place any marble pebbles in front of the pilot light.

Make sure that the pilot light can burn freely over the main

burner.

•

Keep the burner oriﬁ ces unblocked

Only this way a proper ignition of the main burner is ensured.

Once the logs / marble pebbles have been positioned, replace the glass in the appliance,
following the instructions in chapter 4: DISMANTLING

/ ASSEMBLING OF THE

GLASS

1.7.6 Mounting ﬂ ue gas restriction plate

Depending on the length and shape of the concentric ﬂ ue system and the chimney

construction, you should, if indicated, ﬁ t a restriction plate with a certain width (B) into
the ceiling of the combustion chamber.
To do this, see the set-up options as listed in ﬁ gure 4 through 14.

Marble pebbles must not be placed
next to the pilot light burner

Keep the burner
oriﬁ ces unblocked

Summary of Contents for VIEW BELL TOPSHAM 3 LF













































































Search results

Summary of Contents for VIEW BELL TOPSHAM 3 LF

Reviews:

Related manuals for VIEW BELL TOPSHAM 3 LF

Brands by name

Popular brands

Bellfires VIEW BELL TOPSHAM 3 LF, Installation Instructions & Manual For Maintenance

Search results

Summary of Contents for VIEW BELL TOPSHAM 3 LF

Reviews:

Related manuals for VIEW BELL TOPSHAM 3 LF

Brands by name

Popular brands