How to adjust the height of the safety harness
Group 0+
Place the child seat on the ground.
Tilt the child seat completely
backwards.
Place the child in the child seat.
Make sure that the harness is adjusted
to the closest position to the child's
shoulders and preferably positioned
just above the child's shoulders (fig. 2).
Group 1
Place the child seat on the ground.
Make sure the car seat is fully upright.
Place the child in the child seat.
Make sure the harness is adjusted
to the closest position to the child's
shoulders and preferably positioned
just above the child's shoulders (fig. 3).
How to move the child seat’s safety harness (fig. 4
– 10)
Tilt the child seat completely backwards.
Press the adjuster (C) and simultaneously pull both
safety harness straps (fig. 4).
Release one safety harness strap from the T-shaped yoke
(P) located behind the backrest of the car seat (fig. 5).
Pull out the harness from the backrest (fig. 6).
Pull out the metal yoke (O) from the backrest (fig. 7).
Insert the metal yoke (O) (fig. 8) and the harness at the
desired height (fig. 9).
Fasten the harness to the T-shaped yoke (P) (fig. 10).
Repeat these steps with the other strap.
Pull the adjuster strap (D) after carrying out all the
steps.
Warning: make sure that the harness straps pass
through the padding (L) and that the rubber part is facing
the child’s body.
Warning: make sure that the harness straps are not
twisted and that the metal buckle cannot slide off of the
backrest.
Adjusting the tilt of the child seat (fig. 11)
Push the tilt adjustment handle upwards (E) and at the
same time move the child seat forwards or backwards
until it reaches the desired tilt (fig. 11).
Warning: after releasing the handle, always check
to make sure the child seat is locked into the chosen
position.
How to use the child seat (fig. 12)
Group
Position of the child seat on the car
seat (fig. 12)
0+
not facing the vehicle's direction of
travel.
1
facing the vehicle's direction of travel.
Position the child seat on one of the vehicle’s back seats
or on the front passenger seat.
Warning: in some countries, the Highway Code prohibits
the use of child seats on front seats: check the Highway
Code of the country you are driving in.
Warning: do not use the child seat on the front seats if
there is an active airbag (only for Group 0+).
Warning: do not place the child seat on a seat that is only
fitted with a lap belt.
Warning: do not put anything between the child seat and
the car seat.
How to install the child seat (fig. 13 – 20)
Group 0+ (up to 13 kg) (fig. 13 - 17)
Warnings: Use the newborn insert (B) for children
less than three months old.
Warning: the child seat must not face the vehicle’s
direction of travel.
Warning: do not use the child seat on the front seats if
there is an active airbag.
How to install the child seat (fig. 13 – 17)
Tilt the child seat completely backwards.
Position the child seat on the car seat by pushing it
against the backrest (fig. 13).
Make sure the base (H) is well positioned on the car
seat.
Warning: The areas where the seat belts need to be
inserted are marked in blue. Do not insert the car’s seat
belts in positions other than the indicated ones.
Identify the areas where the car’s seat belt needs to be
inserted.
Pass the seat belt between the base (H) and the seat
(A) (fig. 14).
Close the car seat belt.
Pass the lap section of the car’s seat belt through both
guides (G) located at the front of the base (fig. 15).
Pass the diagonal section of the car’s seat belt through
the guides (K) located at the back of the base (fig. 16).
Fasten the blue belt lock (F) around the car’s seat
belt, as close as possible to the buckle (fig. 17).
Warning: the car’s seat belts must be tightened to
prevent the child seat from moving.
Warning: make sure the car’s seat belt is not twisted.
SUGGESTIONS
If the car's seat belt seems to be too short:
•
make sure the child seat has been pushed properly
against the car seat's backrest;
•
if possible, move the car seat backwards as far as
you can;
•
if possible, adjust the height of the car's seat belts
to the lowest position.
How to remove the child seat from the car
Release the car’s seat belt.
Pull out the seat belt from the child seat and allow it to
retract.
Group 1 (from 9 to 18 kg) (fig. 18 – 20)
Warning: the child seat must face the vehicle’s direction
of travel.
How to install the child seat (fig. 18 – 20)
Position the child seat on the seat of the vehicle so that it
EN
9
Summary of Contents for Augusto
