BC 350 Operators Manual
BC 350 Operators Manual
5
GB
CAUTION
!
General Safety
Pre-start Checks
Pre start-up inspection
The following Pre-start-up inspection must be performed before the start of each work
session or after every four hours of use, whichever is first. Please refer to the service
section for detailed guidance. If any fault is discovered, the floor saw must not be used
until the fault is rectified.
1. Thoroughly inspect the BC 350 saw for signs of damage.
Check components are present and secure. Pay special attention to the blade
safety guard.
2. Check fluid lines, hoses filler openings, drain plugs and any other areas for
signs of leakage. Fix any leaks before operating.
3. Check the machine is connected to electrical earthing.
4. Check all cables are protected from damage and are not likely to be tripped over.
GB
GB
For your own personal protection and for the safety of those around you, please read
and ensure you fully understand the following safety information.
It is the responsibility of the operator to ensure that he/she fully understands how to
operate this equipment safely. If you are unsure about the safe and correct use of the
Ambassador Saw, consult your supervisor or Belle Group.
•
This equipment is heavy and must not be lifted single-handedly, either
GET
HELP
or use suitable lifting equipment.
•
Cordon off the work area and keep members of the public and unauthorized
personnel at a safe distance.
•
Personal Protective Equipment (PPE) must be worn by the operator when ever this
equipment is being used (see Health & Safety).
•
Make sure you know how to safely switch this machine
OFF
before you
switch it
ON
in case you get into difficulty.
•
Always switch
OFF
the motor before transporting, moving it around the site
or servicing it.
•
During use the motor becomes very hot, allow the motor to cool before
touching it. Never leave the motor running and unattended.
•
Never remove or tamper with any guards fitted, they are there for your
protection. Always check guards for condition and security, if any are damaged or
missing,
DO NOT USE THE BC 350 SAW
until the guard has been replaced or
repaired.
•
DO NOT OPERATE THE BC 350 SAW
when you are ill, feeling tired, or when under the
influence of alcohol or drugs.
•
The BC350 Saw should not be used in the rain, or any other harsh weather
conditions.
Improper maintenance can be hazardous. Read and Understand this
section before you perform any maintenance, service or repairs.
12
Warranty
Your new Belle Group BC350 Bench Saw is warranted to the original purchaser for
a period of one-year (12 months) from the original date of purchase.
The Belle Group warranty is against defects in design, materials and workmanship.
The following are not covered under the Belle Group warranty:
1. Damage caused by abuse, misuse, dropping or other similar damage caused
by or as a result of failure to follow assembly, operation or user maintenance
instructions.
2. Alterations, additions or repairs carried out by persons other than Belle
Group or their recognized agents.
3. Transportation or shipment costs to and from Belle Group or their recognized
agents, for repair or assessment against a warranty claim, on any machine.
4. Materials and/or labour costs to renew, repair or replace components due to
fair wear and tear.
The following components are not covered by warranty.
· Drivebelt/s
· Engine air filter
· Engine spark plug
Belle Group and/or their recognized agents, directors, employees or insurers will not
be held liable for consequential or other damages, losses or expenses in connection
with or by reason of or the inability to use the machine for any purpose.
Warranty Claims
All warranty claims should firstly be directed to Belle Group either by telephone, by
Fax, by Email, or in writing.
Tel: +44(0) 1538 380000 Fax: +44(0) 1538 380038
Email : [email protected]
Write to:
Belle Group Warranty Department,
Unit 5 Bode Business Park,
Ball Haye Green,
Leek,
Staffordshire, ST13 8BW,
England.
GB
