manualshive.com logo in svg

Belden grass valley MASTERPIECE 12G-SDI, Installation Manual

Share
Download
Belden grass valley MASTERPIECE 12G-SDI Installation Manual Download Page 35

19

[PRODUCT NAME]

[DOCUMENT TYPE]

Mainframe Location and Environment

Location Instructions

The Masterpiece mainframe can be used freestanding (tabletop configuration) or installed in a 
standard 483mm (19 inch) equipment rack. The following precautions should be observed:

1 The air intakes on both sides and the cooling fan exhausts at the rear of the unit must not 

be obstructed - a minimum clearance at the rear of the mainframe of 200mm (8 inches) is 

ESSENTIAL

.

2 Air intakes situated at the front and on both sides, are to allow the inlet of cooling air and 

MUST NOT BE OBSTRUCTED.

Cooling Fan Failure

IF THE COOLING FANS ONTHE SWITCHER MAINFRAME SHOULD STOP FOR ANY REASON, THEN 
THE SYSTEM SHOULD BE SWITCHED OFF IMMEDIATELY OR PERMANENT DAMAGE MAY RESULT.
Depending on the length of time the mainframe has been run with no fan the unit may need to 
be returned for checking and repair. Contact SAM or your SAM dealer to discuss the situation.

Warning!

Side view of the Masterpiece
mainframe showing
airflow through

Fans are located
on the front door
of the mainframe

Top view of the 
Masterpiece
Mainframe showing
Airflow through the
chassis

Note:

Do not obstruct air intakes to fans and air vents on any piece of 

equipment listed in this manual. Please pay particular attention to the air 
intakes at sides and the vents at the rear of the Mainframe.

Summary of Contents for grass valley MASTERPIECE 12G-SDI


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands