manualshive.com logo in svg

Belden grass valley MASTERPIECE 12G-SDI, Installation Manual

Share
Download
Belden grass valley MASTERPIECE 12G-SDI Installation Manual Download Page 17

 1

About this Manual

Overview

Thank you for purchasing your new Masterpiece Master Control Switcher.

This installation manual will help you through each stage of the physical installation of each 
component and advise you of all relevant safety aspects. For user setup and configuration 
please consult the User Instruction Manual.

If you have any questions regarding the installation of your product, please refer to the contact 
details listed at the rear of this manual.

Masterpiece 12G-SDI Mainframe

Masterpiece Control Surface

Masterpiece IP Mainframe

Note:

Please note

 that all diagrams are for illustration purposes only and 

may differ slightly from the purchased product. SAM operates a policy of 
continuous improvement and development. SAM reserves the right to make 
changes and improvements to any of the products described in this 
document without prior notice.

Summary of Contents for grass valley MASTERPIECE 12G-SDI


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands