background image

TCP3500-1024G

 

5

 

 

 

 

Asia-Pacific 

+86 755 298 85888

 

Europe, Middle East 

+353 61 225 977

 

North America 

+1

 

408

 

785 5200

 

© 2020 Bel Power Solutions & Protection

 

BCM.00495_D 

 

SIGNAL OUTPUT CONNECTOR 

 PINOUT 

SIGNAL NAME 

PIN # 

TYPE 

SIGNAL 

REFERENCE 

LOW LEVEL 

HIGH LEVEL 

V MAX 

I MAX 

RS485-1A 

RS485 Half Duplex, Differential pair 1  

RS485-1B 

+/-60 mA 

@ 60 

Ω

, 50 pF 

-7 to 12 VDC 

8 mA 

RS485-2A 

RS485 Half Duplex, Differential pair 2 

RS485-2B 

+/-60 mA 

@ 60 

Ω

, 50 pF 

-7 to 12 VDC 

8 mA 

ADDR-INIT OUT 

The unit’s address change accepted

 

SRTN 

<0.4 VDC 

Pull up 

7 VDC 
20 mA 

IN OK 

AC Power Fail Warning - open collector, 

external pull-up needed to max. 7 V 

SRTN 

<0.4 VDC 

Pull up 

7 VDC 
20 mA 

OUT OK 

Output Voltage Fault - open collector, external 

pull-up needed to max. 7 V 

SRTN 

<0.4 VDC 

Pull up 

7 VDC 
20 mA 

INHIBIT 

Output Inhibit - 

Open circuit or “High” to SRTN 

shuts OFF Vout 

SRTN 

<0.4 VDC 
>2.5 VDC 

3.6 VDC 

0.2 mA 

ENABLE 

Power Supply Enable pin 

 for unit enable 

short this pin to SRTN 

SRTN 

<0.4 VDC 
>2.5 VDC 

3.6 VDC 

0.2 mA 

SRTN

1

 

Internal Ground (Signal Return) 

RS485-1B 

RS485 Half Duplex, Differential pair 1 

RS485-1B 

+/-60 mA 

@ 60 

Ω

, 50 pF 

-7 to 12 VDC 

8 mA 

RS485-2B 

10 

RS485 Half Duplex, Differential pair 2 

RS485-2B 

+/-60 mA 

@ 60 

Ω

, 50 pF 

-7 to 12 VDC 

8 mA 

Not Connected 

11 

OT/FAIL 

12 

Over Temperature /PSU Fail, open collector, 

external pull-up needed to max.7 VDC 

SRTN 

<0.4 VDC 

Pull up 

7 VDC 
20 mA 

PS-PRESENT OUT 

13 

Power Supply Seated 

 last unit in string will 

pull down this signal (external short to SRTN) 
and informs Master Controller that all units in 

string are seated and connected 

SRTN 

<0.4 VDC 
>2.5 VDC 

3.6 VDC 

0.2 mA 

ACSH 

14 

Active Current Share 

SRTN 

0.2 VDC 
5.0 VDC 

7 VDC 

0.7 mA 

Margin 

15 

Optional 

 analog signal for Output Voltage 

adjustment - Not Connected 

SRTN 

1

   SRTN and Vout- are connected together inside the power supply.  

Note:

 Maximal mounting torque for the screw locks of the signal connector is 0.3 Nm (please see the Fig. 1)

 

 

Connector type:    Würth Elektronik, 61801529321 
Mating part: 

   Würth Elektronik, 61801529221 

Summary of Contents for TCP3500-1024G







Reviews: