5 / EN
Washing Machine / User’s Manual
2 Installation
Refer to the nearest Authorised Service Agent for
installation of the product. To make the product
ready for use, review the information in the user
manual and make sure that the electricity, tap water
supply and water drainage systems are appropriate
before calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber to
have any necessary arrangements carried out.
C
Preparation of the location and electrical,
tap water and waste water installations
at the place of installation is under
customer's responsibility.
B
WARNING:
Installation and electrical
connections of the product must be
carried out by the Authorized Service
Agent. Manufacturer shall not be held
liable for damages that may arise from
procedures carried out by unauthorized
persons.
A
WARNING:
Prior to installation, visually
check if the product has any defects on
it. If so, do not have it installed. Damaged
products cause risks for your safety.
C
Make sure that the water inlet and
discharge hoses as well as the power cable
are not folded, pinched or crushed while
pushing the product into its place after
installation or cleaning procedures.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it
on a long pile rug or similar surfaces.
• Total weight of the washing machine and the
dryer -with full load- when they are placed on top
of each other reaches to approx. 180 kilograms.
Place the product on a solid and flat floor that has
sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where
temperature may fall below 0
°C
.
• Place the product at least 1 cm away from the
edges of other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
2.3 Removing the transportation locks
A
WARNING:
Do not remove the
transportation locks before taking out the
packaging reinforcement.
A
WARNING:
Remove the transportation
safety bolts before operating the washing
machine! Otherwise, the product will be
damaged.
1. Loosen all the bolts with a suitable spanner until
they rotate freely
(C).
2. Remove transportation safety bolts by turning
them gently.
3. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel.
(P)
C
Keep the transportation safety bolts in a safe
place to reuse when the washing machine
needs to be moved again in the future.
C
Never move the product without the
transportation safety bolts properly fixed in
place!
2.4 Connecting water supply
C
The water supply pressure required to run the
product is between 1 to 10 bars (0.1 – 1 MPa).
It is necessary to have 10 – 80 liters of water
flowing from the fully open tap in one minute
to have your machine run smoothly. Attach
a pressure reducing valve if water pressure is
higher.
C
If you are going to use the double water-inlet
product as a single
(cold)
water-inlet unit,
you must install the supplied stopper to the
hot water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
A
WARNING:
Models with a single water inlet
should not be connected to the hot water tap.
In such a case the laundry will get damaged
or the product will switch to protection mode
and will not operate.
A
WARNING:
Do not use old or used water
inlet hoses on the new product. It may cause
stains on your laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet, blue
hose (right) (max. 25 ºC) is for cold water inlet.
Summary of Contents for WRE 6532 B0
Page 2: ......
Page 91: ...91 CZ Plně automatická pračka Uživatel Manuální ...
Page 92: ...www beko com ...
