Beko WMY 81233 LMB3, User Manual

Page: 6 / 84

6 / EN
Washing Machine / User’s Manual
3. Attach the plastic covers supplied in the User Manual bag
into the holes on the rear panel.
(P)
C
Keep the transportation safety bolts in a safe place to
reuse when the washing machine needs to be moved
again in the future.
Never move the product without the transportation safety
bolts properly fixed in place!
2.4 Connecting water supply
C
The water supply pressure required to run the product is
between 1 to 10 bars (0.1 – 1 MPa). It is necessary to
have 10 – 80 liters of water flowing from the fully open
tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is
higher.
If you are going to use the double water-inlet product
as a single
(cold)
water-inlet unit, you must install the
supplied stopper to the hot water valve before operating
the product. (Applies for the products supplied with a
blind stopper group.)
A
WaRNING:
Models with a single water inlet should not
be connected to the hot water tap. In such a case the
laundry will get damaged or the product will switch to
protection mode and will not operate.
WaRNING:
Do not use old or used water inlet hoses
on the new product. It may cause stains on your laundry.
1. Connect the special hoses supplied with the product to
the water inlets on the product. Red hose (left) (max. 90
ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is
for cold water inlet.
A
WaRNING:
Ensure that the cold and hot water
connections are made correctly when installing the
product. Otherwise, your laundry will come out hot at the
end of the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a tool when
tightening the nuts.
3. Open the taps completely after making the hose
connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the
nut. Retighten the nut carefully after checking the seal. To
prevent water leakages and damages caused by them,
keep the taps closed when the machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
A
WaRNING:
Your house will be flooded if the hose
comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing
temperatures! To prevent such situations and to ensure
smooth water intake and discharge of the machine, fix
the end of the discharge hose tightly so that it cannot
come out.
• The hose should be attached to a height of at least 40
cm, and 100 cm at most.
• In case the hose is elevated after laying it on the floor
level or close to the ground (less than 40 cm above the
ground), water discharge becomes more difficult and the
laundry may come out excessively wet. Therefore, follow
the heights described in the figure.
100cm
40cm
• To prevent flowing of dirty water back into the machine
and to allow for easy discharge, do not immerse the hose
end into the dirty water or do not drive it in the drain more
than 15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between
the drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may
not be longer than 3.2 m. To avoid water leak failures,
the connection between the extension hose and the
drain hose of the product must be fitted well with an
appropriate clamp as not to come off and leak.
2.6 adjusting the feet
A
WaRNING:
In order to ensure that the product
operates more silently and vibration-free, it must stand
level and balanced on its feet. Balance the machine
by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration
problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and
balanced.
3. Tighten all lock nuts again by hand.