background image

5.19  Local total reset:   

Clr tot

Clr tot

 is a sub-menu in the 

LoC CLr

 function. When

activated  it  allows  an  operator  to  reset  the  total
display to the reset value [see section 5.17] while
the BA567E-SS Counter is in the display mode by
operating  the  

&

 and  

*

 push  buttons

simultaneously for more than three seconds.

To check or change the setting select 

LoC CLr

 in the

configuration menu and press  

(

 which will reveal

the 

Clr tot

 prompt, operating 

(

 

again will show

 

if

the local total reset is 

on

 or 

oFF

.   If set as required

operate  the  

)

  button  twice  to  return  to  the

configuration  menu,  or  the  

&

 or  

*

 button  to

change the setting followed by the  

)

 button twice

to enter the change and return to the 

LoC CLr

 prompt

in the configuration menu.

Note:

The total display may also be remotely reset
to  the  reset  value  by  connecting  terminals
RS1  and  RS2  together  for  more  than  one
second.  See sections 3.3 of this manual.

6.20  Local grand total reset:   

Clr Gtot

The grand total is a separate sixteen digit counter
which is incremented or decremented in parallel with
the   total   display,   but   is   not   reset   when   the   total
display is reset.  The grand total may be viewed in
the  display  mode  in  two  eight  digit  sections  as
described in section 2.2 of this manual.

Clr  Gtot

  is  a  sub-menu  in  the  

LoC  CLr

 function

which  when  activated  allows the  operator to reset
the grand total display to zero from the display mode
by  operating  the  

)

 and  

*

 push  buttons

simultaneously for more than ten seconds.

To  check  or  change  setting  select  

LoC  CLr

 in  the

configuration menu and press  

(

 which will reveal

Clr tot

.  Using the 

&

 or 

*

 button select 

Clr Gtot

and  press  

(

 

which  will  show

 

if  local  grand  total

reset is 

on

 or 

oFF

.   If set as required operate the 

)

button twice to return to the configuration menu, or
the 

&

 or 

*

 button to change the setting followed

by  the  

)

  button  twice  to  enter  the  change  and

return  to  the  

LoC  CLr

  prompt  in  the  configuration

menu.

Note:

 

Once  reset,  the  grand  total  can  not  be
recovered.

5.21   Reset grand total from configuration menu:
          

Clr  Gtot

The grand total is a separate sixteen digit counter
which is incremented or decremented in parallel with
the  total  display,  but  is  not  reset  when  the  total
display is reset.  The grand total may be viewed in
the  display  mode  in  two  eight  digit  sections  as
described in section 2.2 of this manual.

To zero the grand total from within the configuration
menu select 

CLr Gtot

 and press 

(

 

which will cause

the instrument to display  

Clr

 

.

 

no

 with  

no

 flashing.

Using the  

&

 or  

*

 push button change  

Clr no  

to

clr  ye5,  

pressing

 

(

  will  result  in  the  instrument

displaying 

0000

 with the first digit flashing.  This is a

request to confirm the reset instruction by entering

5urE

.     Using   the  

&

 or  

*

 button  set  the  first

flashing digit to 

5

 and press 

(

 to transfer control to

the second digit which should be set to  

u

.   When

5urE

 has been entered pressing the  

)

 button will

reset the grand total which will be confirmed by a
brief  display  of  

Gt  Clrd

,   the   instrument   will

automatically  return  to  the  

Clr  Gt

 prompt  in  the

configuration menu.

Note:

 

Once  reset,  the  grand  total  can  not  be
recovered.

5.22  Security code:  

CodE

Access to the instrument configuration menu may be
protected by a four digit security code which must be
entered  to  gain  access.      New  instruments  are
configured with the default security code 0000 which
allows  unrestricted  access  to  all  configuration
functions.

To enter a new security code select  

CodE

 from the

configuration menu and press

 

(

 which will cause

the  BA567E-SS  Counter  to  display  

0000

 with  one

digit  flashing.   The  flashing  digit may  be  adjusted
using  the  

&

 and  

*

  push  buttons,  when  set  as

required operating the 

(

 button will transfer control

to the next digit.   When all the digits have been
adjusted press

 

)

 to return to the 

CodE

 prompt. The

revised  security  code  will  be  activated  when  the
BA567E-SS Counter is returned to the display mode.

Please contact BEKA associates sales department if
the security code is lost.

18

Summary of Contents for BA567E-SS

































Reviews: