BEKA BA334D Manual Download

Page: 39 / 43

the ‘E’ terminal on the terminal block.

Article 250 of the National Electrical Code the enclosures shall be grounded using

The BA334D enclosure is manufactured from conductive plastic per

hubs are fitted to a BA334D, all metallic glands or conduit hubs must be connected

In addition to the supplied bonding plate, when 2 or 3 metallic glands or conduit

with cable glands / conduit hubs selected from the following table.

When installed in a hazardous (classified) location the BA334D shall be fitted

Any metallic or plastic cable gland or conduit hub that provides

SSTG-1 STG-1 STAG-1

Permitted gland or conduit hub

Killark Glands

together and grounded.

10.

CAUTION:

CMCXAA050 MCR050 MCX050

Metallic glands and hubs must be grounded – see note 9.

Class I

Class II and III

Class

CHMG-50DT

Crouse – Hinds Myler hubs

the required environmental protection.

O-Z / Gedrey hubs

MHUB-1

REMKE hub

WH-1-G

A1 & A2 and A3 & A4 shall be installed as separate intrinsically safe circuits in
accordance with the National Electrical Code.

Circuit connections to terminals 1 & 2; 7 & 8; B1 & B2; P1 & P2; C1 & C2;

11.

Summary of Contents for BA334D












































Search results

Summary of Contents for BA334D

Reviews:

Related manuals for BA334D

Brands by name

Popular brands

BEKA BA334D, Manual

Search results

Summary of Contents for BA334D

Reviews:

Related manuals for BA334D

Brands by name

Popular brands