background image

Page  7

N O T E S

1

1

4

 mm

4

0

 mm

58 mm

SGM595
autosetting

ON

78  mm

Cable  Gland    PG13,5

Opening of the Cover.
With  the  help  of  a  screwdriver
to  turn  counterclockwise  for  a
quarter  of  turn

Closeof the Cover.
With  the  help  of  a  screwdriver
to  turn  counterclockwise  for  a
quarter  of  turn

1)  Put  out  all  free  flames.
2)  Close  the  main  gas  tap  or  the  LPG  cylinder  tap.
3)  Do  not  turn  any  lights  on  or  off;  do  not  turn  on  any  electrical  device  or  appliance.
4)  Open  windows  and  doors  in  order  to  increase  ventilation.

If  the  alarm  stops,  its  cause  must  be  found  and  the  relevant  consequent  measures  taken.
If  the  alarm  continues  and  the  cause  of  gas  presence  cannot  be  found  or  removed,  abandon  the  building
and  call  the  emergency  services  when  outside  (fire  department,  distributors,  etc.)
IMPORTANT:  The  operation  test  should  not  be  carried  out  with  the  gas  tap  as  this  does  not  guarantee  a
sufficient  concentration  to  activate  the  general  alarm.

Warning  !!

If  you  have  the  following  symptoms:  vomiting,  sleepiness,  or  else,  go  to  the  closest  first  aid
station  and  inform  the  operators  that  you  could  have  been  poisoned  by  Carbon  Monoxide,  or
by  an  excess  or  deficiency  of  oxygen

WARNING!  Actions  to  be  taken  in  case  of

alarm

Measurements  and  dimensions

Summary of Contents for SGM595









Reviews: