background image

CONFORMITY

Installation and user
guide

Important: Assembly / maintenance of the appliance must be carried out by qualified personnel and in
accordance with applicable laws and regulations.
The manufacturer assumes no responsibility for the use of products that have to comply with particular
environmental and / or installation standards.

Important note
Before connecting the equipment, it is recommended that you read the instruction manual carefully and
keep it for future reference. It is also recommended to perform the electrical connections correctly as
per enclosed drawings, observing the instructions and the Standards.
N.B. Refer to the documentation in all cases where the symbol is on the side

EN 50194
EN 50270

Compliant  EN 60079-29-1

Installation  EN 60079-29-2

Reports issued by  TUV Italia

Channel:  Beinat  gas  solutions

Electric connections also available on

Stand-alone Gas Sensor SG800

                                                          V. R4

The  SG800  is  born  from  the  elegance  and  prestige  that  has  always  distinguished    BEINAT    S.r.l.  and  from
the  home  fitness  concept.
The  probe is a Catalytic gas detection unit with IP66 protection that, together with one of BEINAT’s industrial
type  Control  Units  or  stand-alone,  detects  the  presence  of  esplosive  gas  such  as  Methane,  LPG,  Hydrogen,
Freon,  Chlorine,  Idrogen  Sulphide,    OXYGEN,  and  other  type  of  gas.
The  probe  has  two  danger  levels:
1

st

  LEVEL,  pre-alarm.  This  was  set  at  see  Table  on  page  2

2

nd

  LEVEL,  main  alarm.  This  was  set  at  see  Table  on  page  2

For Oxygen ALARM, for <Oxygen deficiency and > Oxygen Excess

The probe is managed by a microprocessor which not only supplies an alarm signal to the control unit connected
to it, but also allows execution of a self-diagnosis and therefore an AUTOMATIC  CALIBRATION,

 

in order to always

have the maximum detection accuracy.
The self-calibration means the probe adapts in harsh and variable temperature environments, avoiding false alarms
due to anomalous events.
The probe has a 0 ÷ 20 % LEL linear output conforming to the 4 ÷ 20mA standard, for which can be connected
with one of BEINAT's industrial control units.
The important innovation of this probe is:
The possibility to substitute the sensor at the end of the operating cycle or fault by the technician without having
to  send  to  BEINAT  Srl.

Instrument  of  testing  TS1008
To  facilitate  the  reading  of  the  functional  parameters  of  the  probe  as  well  as  the
control  of  annual  operating,  the  BEINAT    S.r.l.    has  built  a  new  portable  tester  TS1008.
The tester allows to read all the data in the memory of the probes eand by serial
transmission, it prints the ticket that confirms the testing data, certifying your own work.

Summary of Contents for SG800









Reviews: