background image

Page  6

Attention!!
The  regulations  described  in  this  paragraph  must  performed  be  authorized  and  specialized  technician  are  suceptibile  to
compromise  the  safety  of  the  survey.
If the device does not start up.
Check  that  the  12/24  Vdc  power  is  present,  and  that  positive  and  negative  polarity  has  not  been  inverted.
If the Fault LED lights up.
If  the  fault  signal  reaches  the  control  unit  connected  to  the  probe.
Check  that  the  cables  are  connected  according  to  the  drawing,  and  that  the  wire  isolation  sheath  has  not  been  pinched.
Check  the  voltage  at  the  terminals  1-2.  It  must  be  higher  than  11Vdc  and  lesser  than  25Vdc.
Check  the  voltage  at  the  terminals  2-3.  It  must  be  from  a  minimum  of  0.8  Vdc  to  a  maximum  of  1.1  Vdc

If  other  problems  arise,  the  Distributor  of  BEINAT    S.r.l.  should  be  contacted  directly.

Troubleshooting

before calling a technician

Description and connecting probe  SG800/Freon - OXYGEN

Led ON

USB data

NC

C

General Alarm

R

5     4     3     2    1

Power supply
  12÷24 V.

Linear output 4-20 mA

The relay is voltage-free.
Contact capacity 1A 48VDC
SELV

USB data

 OXYGEN

FREON

Linear Otput 4-20 mA

3    2    1

R

0

1

3

2

1,1

VDC

Voltmeter

Power Supply
  12÷24 V.

WARNING.

These  measurement  should  be  performed  in
clean air.
Moreover, this test must be performed only with
the probe connected to a control unit, or with a
220 Ohm resistance installed between terminal 2
and terminal 3.

Switch 1 Positive safety
ON 
position: Positive safety  inserted
OFF position: Positive  safety switched off

Switch 2 determination thresholds
ON
 position:
Threshold of intervention from <18.5 to> 23.5 vol

OFF position:
Threshold of intervention from <19.5 to> 22.5 vol

Summary of Contents for SG800









Reviews: