BeiJer BFI-P2 Series, Installation & User Manual, Page: 48 / 84

48
| Beijer BFI-P2 User Guide |
Version 3.04 www.beijerelectronics.com
Par Parameter Name Minimum Maximum Default Units
P2-13 Analog Output 2 Function (Terminal 11) 0 12 9 -
Digital Output Mode. Logic 1 = +24V DC
0 Drive running
Logic 1 when the BFI drive is enabled (Running).
1 Drive healthy
Logic 1 when no Fault condition exists on the drive.
2 At speed
Logic 1 when the output frequency matches the setpoint frequency.
3 Motor speed > 0
Logic 1 when the motor runs above zero speed.
4 Motor speed >= limit
Logic 1 when the motor speed exceeds the adjustable limit.
5 Motor current >= limit
Logic 1 when the motor current exceeds the adjustable limit.
6 Motor torque >= limit
Logic 1 when the motor torque exceeds the adjustable limit.
7 Analog input 2 >= limit
Logic 1 when the signal applied to the Analog Input 2 exceeds the adjustable limit.
NOTE
When using settings 4 – 7, parameters P2-19 and P2-20 must be used together to control the behaviour. The output will switch
to Logic 1 when the selected signal exceeds the value programmed in P2-19, and return to Logic 0 when the signal falls below the
value programmed in P2-20.
Analog Output Mode
8 Motor speed
0 to 100% of P1-01 (Maximum Frequency).
9 Motor current
0 to 200% of P1-08 (Motor Nominal Current).
10 Motor torque
0 to 200% of motor rated torque.
11 Motor power
0 to 150% of drive rated power.
12 PID output
Output from the internal PID Controller, 0 – 100%.
P2-14 Analog Output 2 Format
See Below  - -
 -
0 to10V
 - 10 to 0V
 -
0 to 20mA
 - 20 to 0mA
 - 4 to 20mA
 -
20 to 4mA
P2-15 Relay 1 Function 0 14 1 -
Setting Function Logic 1 when
0 Drive running
The BFI drive is enabled (Running).
1 Drive healthy
No fault or trip condition exists on the drive.
2 At speed
Output frequency matches the setpoint frequency.
3 Motor speed > 0
The motor runs above zero speed.
4 Motor speed >= limit
The motor speed exceeds the adjustable limit.
5 Motor current >= limit
The motor current exceeds the adjustable limit.
6 Motor torque >= limit
The motor torque exceeds the adjustable limit.
7 Analog input 2 >= limit
The signal applied to the Analog Input 2 exceeds the adjustable limit.
8 Reserved
No Function.
9 Reserved
No Function.
10 Maintenance due
The internally programmable maintenance timer has elapsed.
11 Drive ready to run
0 to 150% of drive rated power.
12 Drive tripped
The drive is not tripped, the STO circuit is closed, the mains supply is present and the
hardware enable input present (Digital Input 1 unless changed by the user).
13 STO status
When both STO inputs are present and the drive is able to be operated.
14 PID error >= limit
The PID Error (difference between setpoint and feedback) is greater than or equal to the
programmed limit.
NOTE
When using settings 4 – 7 and 14, parameters P2-16 and P2-17 must be used together to control the behaviour. The output
will switch to Logic 1 when the selected signal exceeds the value programmed in P2-16, and return to Logic 0 when the signal falls
below the value programmed in P2-17.
P2-16 Relay 1 / Analog Output 1 Upper Limit P2-17 200.0 100.0 %
8
Extended P
arameters