background image

Safety Precautions

Caution:

The enclosure provides a degree of protection of at least IP20, but when installed in an
apparatus, it should meet IP54.
LE BOÎTIER OFFRE UN DEGRÉ DE PROTECTION D'AU MOINS IP20, MAIS
LORSQU'IL EST INSTALLÉ DANS UN APPAREIL, IL DOIT ÊTRE DE CLASSE IP54.

1.3 During Installation

The operator panel is designed for stationary installation on a plane surface,
where the following conditions are fulfilled:

no high explosive risks

no strong magnetic fields

no direct sunlight

no large, sudden temperature changes

Install the product according to the accompanying installation instructions.

Ground the product according to the accompanying installation instructions.

Only qualified personnel may install the operator panel.

Separate the high voltage, signal and supply cables.

Make sure that the voltage and polarity of the power source is correct before
connecting the product to the power outlet.

Peripheral equipment must be appropriate for the application and location.

1.4 During Use

Keep the operator panel clean.

Emergency stop and other safety functions may not be controlled from the
operator panel.

Do not use excessive force or sharp objects when operating the touchscreen.

1.5 Service and Maintenance

Only qualified personnel should carry out repairs.

The agreed warranty applies.

Before carrying out any cleaning or maintenance operations, disconnect the
equipment from the electrical supply.

Clean the display and surrounding front cover with a soft cloth and mild
detergent.

Replacing the battery incorrectly may result in explosion. Only use batteries
recommended by the supplier. During the warranty period, the battery needs
to be replaced by an authorized Beijer Electronics service center.

1.6 Dismantling and Scrapping

The operator panel or parts thereof shall be recycled according to local
regulations.

The following components contain substances that might be hazardous
to health and the environment: lithium battery, electrolytic capacitor and
display.

Beijer Electronics, MAEN809F

6

Summary of Contents for EXTER T60


























Reviews: