background image

4

SAFETY 

IMPORTANT SAFETY INSTRUCTIONS

WARNING

WARNING

Failure to follow these instructions and observe the warnings 

provided in this operations manual could result in fire, 

explosion or burn hazard, which could cause property damage, 

personal injury or death.

Gas vapour is highly explosive and can cause serious bodily 

injury or damage to property if allowed to accumulate in a 

confined space and ignited.
This appliance must not be installed under or on any 

combustible material. Minimum clearance from combustible 

materials to all sides of the appliance is 450mm (18”).
These instructions must be left with the owner.
NOTE:
1.

      

Do not use gas other than the type specified on the  

Data Plate.

2.

      

The appliance is designed for use by adults, keep children 

away from the barbecue at all times.

3.

      

Use only on a flat, level, stable non-combustible surface. Do 

not use this appliance on any surface that can burn or melt.

4.

      

When in use, gas cylinder should be kept at designated 

mountings of barbecue, and supply hoses kept away from 

any hot surfaces.

5.

      

To prevent accidental fires, before using the appliance 

ensure that there is no apparent damage to hose and 

regulator and all joint connections are in good order and not 

leaking.

6.

      

Use a soapy water solution on all joints in order to check for 

leaks. If bubbles appear, it indicates that there is a leak and 

the appliance must not be used.

7.

      

LPG cylinder, regulator and hose must comply with national 

standards.

8.

      

Do not move or attempt to move the appliance while in 

operation.

9

      

Do not operate this appliance before leak checking hoses 

and gas cylinder connection.

To the installer

•    

  

For fixed installations, in Australia refer also to the 

requirements of AS/NZS5601, local authority, gas, 

electricity, and any other relevant statutory regulations.

•    

 

For fixed installations, refer to AS/NZS5601 for pipe sizing 

details.

•    

 

Consult other trades. Where required, consult a bricklayer 

or an electrician for parts of the installation that could have 

an effect on these areas.

•    

 

Allow a 20mm gap from back of barbecue body for 

ventilation and air access.

•    

 

Test appliance for correct operation before leaving, and 

instruct user on its use.

•    

 

If correct operation cannot be achieved, disconnect 

barbecue from gas supply, and contact your nearest 

BeefEater dealer.

•    

 

Please only use BeefEater supplied hose(s) to connect this 

appliance. Natural Gas conversion kits are available from 

your nearest BeefEater dealer.

•    

 

Australia only (applies to all gas types) : Where a mobile 

appliance is to be connected to a fixed gas supply via a 

flexible hose connection, a retaining tether of adequate 

strength shall be fixed to the appliance and be suitable 

to be fixed to the wall within 50mm of each connection 

point. The length of the tether shall not exceed 80% of the 

length of the hose assembly. In this way, if the barbecue 

is accidentally moved, the tether stops the barbecue from 

stretching the hose.

Do not

•      Lean over barbecue when lighting.
•      Leave cooking food unattended.
•      Delay lighting burners after turning gas on.
•      Spray or store aerosols in vicinity of barbecue whilst  

in operation.

•    Place articles on or against this appliance
•      Store combustible materials, gasoline or flammable liquids 

or vapours within 450mm (18”) of barbecue.

•      Use caustic based cleaning agents on the barbecue.
•      Operate barbecue with any cover on.
•      Use plastic or glass utensils on the barbecue.
•      Operate barbecue in strong winds.
•      Attempt to dismantle control valves.
•      Attempt to dismantle or adjust regulator.
•      Test for gas leaks with a naked flame.
•      Store gas cylinder indoors, or in any enclosed area.
•      Lay the gas cylinder down. Always keep it upright.
•    

  Use  barbecue  indoors.

•      Expose hose to direct sunlight.
•      Modify the construction of this appliance or the size of any 

burner or valve orifice.

Summary of Contents for 1200 Series

































Reviews: